Filter
Top Products
21
ENGLISH
OTHER OPERATION
Use the TUNING/PRESET knob !4 or pressing the
CHANNEL/CONTROL button ⁄4 to select the last day.
Then press the TUNING/PRESET knob !4 or
ENTER button v.
10
.Set the On time.
q
Either turn the TUNING/PRESET knob !4 or press
the CHANNEL/CONTROL button ⁄4 to adjust the
hour for the On time and press the TUNING/PRESET
knob !4 or ENTER button v.
w Either turn the TUNING/PRESET knob !4 or press
the CHANNEL/CONTROL button ⁄4 to adjust the
minutes for the On time and press the
TUNING/PRESET knob !4 or ENTER button v.
11
.Set the Off time.
q Either turn the TUNING/PRESET knob !4 or press
the CHANNEL/CONTROL button ⁄4 to adjust the
hour for the Off time and press the
TUNING/PRESET knob !4 or ENTER button v.
w Either turn the TUNING/PRESET knob !4 or press
the CHANNEL/CONTROL button ⁄4 to adjust the
minutes for the Off time.
12
.Set the timer program.
q Press the TUNING/PRESET knob !4 or ENTER
button v to decide the timer program setting.
Timer indicator lights up and setting contents are
scrolled.
Note
• Timer program can activate regardless of power on or
standby mode.
• When timer program is finished, the unit goes to standby
mode.
• You can cancel the Timer program setting procedure at
any time by pressing the TIMER button ⁄7.
7
Confirm and change timer program
• You can check and change the timer program setting as
follows.
1. Press the TIMER button ⁄7.
2. Either turn the TUNING/PRESET knob !4 or press the
CHANNEL/CONTROL button ⁄4 to select timer program
number.
3. You can change the displayed contents with the
TUNING/PRESET knob !4 or CHANNEL/CONTROL ⁄4
and ENTER buttons v if necessary.
Note
• Timer program is not changed if you quit confirming
halfway through a procedure.
7
Timer program off
1. Press the TIMER button ⁄7, “TIMER PROGRAM 1” is
displayed.
2. Either turn the TUNING/PRESET knob !4 or press the
CHANNEL/CONTROL button ⁄4 to select timer program
number.
3. Press the TUNING/PRESET knob !4 or ENTER button
v, “TIMER PROGRAM x SET” is displayed.
4. Either turn the TUNING/PRESET knob !4 or press the
CHANNEL/CONTROL button ⁄4 to select “TIMER
PROGRAM x OFF”.
5. Press the TUNING/PRESET knob !4 or ENTER button
v to turn off the timer program.
Note
• To turn a timer program back on again, repeat this
procedure and select “TIMER PROGRAM x ON”.
REMOTE CONTROLLER
RC7001ST
SHIFT
R
E
E
N
T
BAND MENU
TUNING
CONTROL
CHANNEL/
A/B C/D E/F
TIMER
10
DISPLAYDIMMER
987
456
32
T-MODEI/JG/H
SLEEP MEMO
ONSTANDBY
1
/A-TUNE
A-PRESET
⁄7
v
⁄4
PUSH ENTERPUSH ENTER
TUNING/PRESETTUNING/PRESET
STEREOSTEREOTUNEDTUNEDTIMERTIMERSLEEPSLEEP
BAND SELECTBAND SELECT
A—PRESETPRESET
MENUMENU
DISPLAYDISPLAY
CATEGORYCATEGORY
STANDBYSTANDBY
ON/STANDBYON/STANDBY
POWERPOWER
FM/AM TUNER ST7001FM/AM TUNER ST7001
!4