Filter
Top Products
20
EN
ENGLISH
5
Adjust the speaker volume level.
From your usual listening position, adjust the volume levels. The
volume levels from each speaker should be the same.
• The receiver enters the speaker volume level adjustment mode.
• Indicators appear only for the channels of the speakers selected
in step 4.
Be aware that the TEST TONE is quite a loud sound (0dB).
1 Press the
∧∧
∧∧
∧/
∨∨
∨∨
∨
keys or @/#keys to select TEST TONE.
2 Press the SETUP key for the following displays:
1 T.TONE AUTO
2 T.TONE MANUAL
3 The selection of AUTO/MANUAL TEST TONE is done by the
MULTI CONTROL knob or Multi (%/fi) keys.
Press the SETUP key again to begin TEST TONE.
Use the MULTI CONTROL knob or Multi (%/fi) keys to adjust
the volume level of the test tone output from the speaker
channel to be adjusted.
For AUTO selection, the first test tone is heard from the Front
Left Speaker for 2.5 seconds. The next test tone is heard from
the speakers in the following sequence for 2 seconds each.
LEFT CNTR RIGHT SR
SBL SBRSLSUBW
The channel indication blinks while the test tone is being output.
L
SL S SB SR
CR
SP MUTE
OPTICAL 6CH INPUT
COAXIAL ANALOG 96kHzfs
CINEMA EQ.
ACTIVE EQ.
DSP MODE
DTS.
MATRIX
DISCRETE
DOLBY DIGITAL
PRO LOGIC
STEREO
LOUDNESS
NEO:6
CSII
AB CLIP
AUTO DETECT THX
AUTO
RDS
RTY
MEMO
STEREO
TUNED
Surround EX
SW
LFE
• If you change the volume level settings for the speakers while
listening to music, the settings referred to on this page are also
changed. fl
• If the speaker setting selects are OFF, the speaker level settings
are reset.
For MANUAL selection, press the
∧∧
∧∧
∧/
∨∨
∨∨
∨
keys or @/# keys each
time to select the speaker channel.
4 Press the SETUP key again.
• The test tone is turned off and return to the main setup displays.
6
Adjust the bass peak level.
A restriction is put on the low frequency so that the bass peak level
will not go higher than the acceptable level when the volume is
increased.
If Subwoofer is OFF, the limitation will affect the low frequency of
the Front Left and Right Speakers.
1 Press the
∧∧
∧∧
∧
/
∨∨
∨∨
∨
keys or @
/
# keys to select BASS PEAK and press
the SETUP key.
SP MUTE
OPTICAL 6CH INPUT
COAXIAL ANALOG 96kHzfs
CINEMA EQ.
ACTIVE EQ.
DSP MODE
DTS.
MATRIX
DISCRETE
DOLBY DIGITAL
PRO LOGIC
STEREO
LOUDNESS
NEO:6
CSII
AB CLIP
AUTO DETECT THX
AUTO
RDS
RTY
MEMO
STEREO
TUNED
Surround EX
SW
LFE
2 Use the MULTI CONTROL knob or Multi (%/fi) keys to adjust
the bass peak level to –30dB.
• The adjustment range is from – 30dB to 0dB and OFF.
Preparing for surround sound
8 Use the MULTI CONTROL knob or Multi (%/fi) keys to select
the appropriate Surround Speaker setting.
If you selected “LARGE” as the Center Speaker setting,
1 SURR NML/THX : Average size Surround Speakers are
connected to the receiver.
2 SURR LARGE : Large Surround Speakers are
connected to the receiver.
3 SURR OFF : Surround Speaker setting mode to
the receiver is OFF.
If you selected other than “LARGE” as the Center Speaker
setting,
1 SURR NML/THX : Average size Surround Speakers are
connected to the receiver.
2 SURR OFF : Surround Speaker setting mode to
the receiver is OFF.
• When the setting “SURR OFF” is selected, you may skip to step
!.
9 Press the
∧∧
∧∧
∧
key or # key again to accept the setting.
• The Surround Speaker setting indication “SB” appears.
0 Use the MULTI CONTROL knob or Multi (%/fi) keys to select
appropriate Surround Back Speaker setting.
If you selected “LARGE” as the Surround Speaker setting,
1 SB NML/THX : Average size Surround Back Speaker is
connected to the receiver.
2 SB LARGE : Large Surround Back Speaker is con-
nected to the receiver.
3 SB OFF : Surround Back Speaker setting mode to
the receiver is OFF.
L
SL S SB SR
CR
SP MUTE
OPTICAL 6CH INPUT
COAXIAL ANALOG 96kHzfs
CINEMA EQ.
ACTIVE EQ.
DSP MODE
DTS.
MATRIX
DISCRETE
DOLBY DIGITAL
PRO LOGIC
STEREO
LOUDNESS
NEO:6
CSII
AB CLIP
AUTO DETECT THX
AUTO
RDS
RTY
MEMO
STEREO
TUNED
Surround EX
SW
LFE
If you selected “NML/THX” as the Surround Speaker setting,
1 SB NML/THX : Average size Surround Back Speaker is
connected to the receiver.
2 SB OFF : Surround Back Speaker setting mode to
the receiver is OFF.
! Press the
∧∧
∧∧
∧
key or # key again to accept the setting.
• The Subwoofer re-mix setting indication “SW RE-MIX” ap-
pears.
@ Use the MULTI CONTROL knob or Multi (%/fi) keys to select
the appropriate Subwoofer re-mix setting.
1 SW RE-MIX ON : Subwoofer re-mix setting mode to
the receiver is ON.
2 SW RE-MIX OFF : Subwoofer re-mix setting mode to
the receiver is OFF.
• If subwoofer is turned off, subwoofer re-mix setting is not visible.
# Press the SETUP key again to return to the main setup
displays.
7 Press the
∧∧
∧∧
∧
key or # key again to accept the setting.
• The Surround Speaker indication “SURR” appears.
04.6.16, 3:53 PM20