Kenwood KIV-BT901 Stereo Receiver User Manual


 
English
|
55
Display Overview
“SMS Inbox” Display the received short message.
Refer to <Display the SMS> (page 61).
“BT Settings”
“Pairing”
“Device
Registration”
Register a Bluetooth device (pairing).
Refer to <Registering Bluetooth Device
(Pairing)> (page 56).
“Phone
Selection”
Select a cell-phone or Bluetooth audio player
connection.
Refer to <Selecting the Bluetooth Device You
Wish to Connect> (page 57).
“Audio
Selection”*
1
“Special Device
Select”
Register a Bluetooth device (pairing).
Refer to <Registering Bluetooth Device
(Pairing)> (page 56).
“Device Delete” Cancel registration of the Bluetooth device.
Refer to <Deleting a Registered Bluetooth
Device> (page 58).
“SMS Download” Download a short message.
Refer to <Downloading the SMS> (page 61).
“Voice Tag” Registers voice for voice recognition and voice
to select the Phone number category in Phone
book.
- Adding a Voice Dialing Command (page 59)
- Setting a Voice Command for Category (page
60)
“Detailed Setup” Move to detailed item.
“PIN Code Edit” Specify the PIN code required when registering
this unit using the Bluetooth device.
Refer to <Registering PIN Code> (page 57).
“Auto Answer”
Answer a call automatically after lapse of the
preset time interval for automatic answer.
“OFF”/ “0s”“8s”“99s”
“Auto
Reconnect”*
2
Automatically reconnects the selected
Bluetooth device when radio wave becomes
strong enough, even after it is disconnected.
“ON”/ “OFF”
When this function is enabled, the
Bluetooth device is reconnected even if
“Phone Selection” is selected to select
a cell-phone connection. To cancel the
Bluetooth connection, select OFF to disable
this function.
“Bluetooth
HF”*
2
“Bluetooth HF/
Audio”*
1
You can specify output speakers for hands-free
voice communication and Bluetooth audio
sound.
“Front”: Outputs voice from the front speakers.
“All”: Outputs voice from the front and rear
speakers.
“Call Beep”
You can output a beep from the speaker when
a call comes in.
“ON”: Beep is heard.
“OFF”: Beep is canceled.
“BT F/W Update” Display the version of the firmware of this unit.
“Mic Gain”*
3
Adjust the sensitivity of the microphone for a
telephone call. Adjust the voice of caller. Setting
to “+” increases the voice volume.
“–3”“0”“+3”
“Noise
Reduction”*
3
Reduce the noises generated by surrounding
environment without changing the microphone
volume. Adjust the voice of caller when it is
not clear. Setting to “+” increases the noise
reduction.
“–3”“0”“+3”
“Echo Cancel
Level”*
3
Adjust the level of echo cancellation. Setting to
“+” increases the echo cancel reduction.
“–2”“0”“+2”
( : Factory setting)
*
1
Function of KIV-701 with KCA-BT300/BT200 (Optional
Accessory)
*
2
Function of KIV-BT901
*
3
Function of KIV-BT901/ KIV-701 with KCA-BT300
(Optional Accessory)
4
Make a setting
Turn the [Volume] knob to select a setting
value, and then press the [Volume] knob.
5
Exit BT Setting mode
Press the [MENU] button for at least 1 second.
6
Exit Bluetooth mode
KIV-BT901: Press the [ ] button.
KIV-701: Press the [iPod] button for at least 1
second.
Remarks
• “Auto Answer” (Setting the Time Interval for Automatic
Answer)
This function automatically answers (responds to) a call
after lapse of the preset time interval for automatic answer.
“OFF” : Does not answer the phone call automatically.
“0” : Automatically answers the phone call at once.
“1s” – “99s” : Automatically answers the phone call after
lapse of 1 – 99 seconds.
• If the time set in the cell-phone is shorter than that set in
the unit, the former will be used.
• This function does not work for call waiting.
• “BT F/W Update” (Displaying the Firmware Version)
Display the version of the firmware of this unit.
For how to update the firmware, access our web site.
http://www.kenwood.com/cs/ce/bt/