Filter
Top Products
20
EN
Preparing for playback
! Use the MULTI CONTROL % / fi (or the % / fi keys) to
select the appropriate BS/SW amp setting.
1 "BS/SW BS":
Select this setting when a surround back speaker is
connected to the SURR BACK/SW terminals. In this
case, the subwoofer signal will be output from the PRE
OUT SUBWOOFER jack.
2 "BS/SW SW":
Select when the subwoofer speaker is connected to the
SURR BACK/SW terminals. In this case, the surround
back signals will be output from the PRE OUT SUR-
ROUND BACK jacks.
3 "BS/SW OFF":
Select when no speaker is connected to the SURR
BACK/SW terminals. In this case, the subwoofer signal
will be output from the PRE OUT SUBWOOFER jack and
the surround back signals will be output from the PRE
OUT SURROUND BACK jacks.
÷ If "BS/SW BS" is selected, only one surround back
speaker can be connected to the receiver.
÷ If "BS/SW SW" or "BS/SW OFF" is selected, two sur-
round back speakers can be connected to the PRE OUT
SURROUND BACK jacks through an external power
amplifier. $
@ Use the MULTI CONTROL # (or the # key) to accept
the setting.
÷ The subwoofer re-mix setting indication "REMIX" appears.
# Use the MULTI CONTROL % / fi (or the % / fi keys) to
select the appropriate subwoofer re-mix setting.
If "REMIX ON" is selected as the subwoofer re-mix setting,
the low frequencies are enhanced by adding the low fre-
quencies of other channels to the subwoofer channel
depending on the speaker setup.
1 "REMIX ON" :
Subwoofer re-mix setting mode to the receiver is ON.
2 "REMIX OFF" :
Subwoofer re-mix setting mode to the receiver is OFF.
÷ The initial setting is "REMIX ON".
÷ The subwoofer re-mix setting is possible only when the
subwoofer setting is "SUBW ON" and the front speaker
setting is "FRNT LRG".
$ Press the ENTER. If your selection is correct, press
the MULTI CONTROL % / fi (or the % / fi keys) to se-
lect "OK".
Press the ENTER again to return to the main setup
displays.
÷ Select "CANCEL" and press the ENTER to return to the
status before setup.
6
Adjust the speaker volume level.
From your usual listening position, adjust the volume levels. The volume
levels from each speaker should be the same.
÷ In steps 6, indications appear only for the selected channels of the
speakers that require adjusting.
1 Use the MULTI CONTROL @ / # (or the @ / # keys) to
select "SP LEVEL" on setup displays, and press the
ENTER.
2 Use the MULTI CONTROL @ / # (or the @ / # keys) to
select "AUTO", "MANUAL" or "OFF".
1 "AUTO": Select this setting to adjust the speaker volume
levels using the test tone. The test tone will be output from
every speaker channel in automatic sequence.
2 "MANUAL": Select to select the speaker channel to
output the test tone using the MULTI CONTROL@ /
# (or the @ / # keys).
3 "OFF": Select to adjust the speaker volume levels
using the current output signals. The speaker chan-
nel to output the output signal can be selected using
the MULTI CONTROL@ / # (or the @ / # keys).
4 "EXIT": Press the ENTER again to return to the main
setup displays.
When "AUTO" or "MANUAL" is selected and the ENTER
is pressed again, the test tone output will start.
Use the MULTI CONTROL % / fi (or the % / fi keys) to
adjust the volume level of the test tone output from the
speaker channel to be adjusted.
For
"
AUTO
"
selection, the first test tone is heard from
the front left speaker for 2 seconds. The next test tone
is heard from the speakers in the following sequence
for 2 seconds each.
When the "BS/SW BS" has been selected :
When the "BS/SW SW" or "BS/SW OFF" has been selected:
The channel indication blinks while the test tone is being output.
÷ When a speaker setup is set to off the volume level for
the corresponding speakers is reset to 0 dB.
When "MANUAL" or "OFF" is selected, press the MULTI
CONTROL @/# (or the @/# keys) to select the speaker
channel and then press the MULTI CONTROL %/fi (or the
%/fi keys) to adjust the speaker volume level.
3 Press the ENTER again to return to the main setup dis-
plays.
÷ The test tone is turned off and return to the main setup
displays.
Continued to next page