Filter
Top Products
5
Getting started
Putting batteries in the remote control
Before using the remote control, put two supplied batteries first.
• When using the remote control, aim the remote control directly at
the remote sensor on the front panel.
1
Press and slide the
battery cover on the back
of the remote control.
2
Insert batteries.
Make sure to match the polarity:
(+) to (+) and (–) to (–).
3
Replace the cover.
If the range or effectiveness of the remote control decreases, replace
the batteries. Use two R6P(SUM-3)/AA(15F) type dry-cell batteries.
• Supplied butteries are for initial setup. Replace for continued use.
CAUTION:
Follow these precautions to avoid leaking or cracking cells:
• Place batteries in the remote control so they match the polarity:
(+) to (+) and (–) to (–).
• Use the correct type of batteries. Batteries that look similar may
differ in voltage.
• Always replace both batteries at the same time.
• Do not expose batteries to heat or flame.
Setting the voltage selector (RX-ES1SL)
Before connections, always do the following first if necessary.
Select the correct voltage in VOLTAGE SELECTOR on the rear of
the receiver by using a screw driver. Check to be sure if the voltage
mark is set to the voltage for your area where this unit plugs in.
Precautions
General precautions
• DO NOT disassemble the unit or remove screws, covers, or cabinet.
• DO NOT expose the unit to rain or moisture.
• DO NOT expose the unit to direct sunlight or place it near a heating
device.
Locations
• Install the receiver in a location that is level and protected from
moisture and dust.
If water gets inside the unit, turn off the power and remove the plug
from the outlet, then consult your dealer. Using the unit in this state
may cause a fire or electrical shock.
• Select a place which is level, dry and neither too hot nor too cold
between 5˚C and 35˚C
• Make sure there is good ventilation around the receiver. Poor
ventilation could cause overheating and damage the receiver.
• Leave sufficient distance between the unit and the TV.
• Do not install the unit in a place subject to vibrations.
Handling the receiver
• DO NOT touch the power cord with wet hands.
• DO NOT pull on the power cord to unplug the cord. When
unplugging the cord, always grasp the plug so as not to damage the
cord.
• Keep the power cord away from the connecting cords and the
antenna. The power cord may cause noise or screen interference. It
is recommended to use a coaxial cable for antenna connection,
since it is well-shielded against interference.
• When a power failure occurs, or when you unplug the power cord,
the preset settings such as preset FM or AM channels and sound
adjustments may be erased in a few days.
• When you are away on travel or otherwise for an extended period or
time, remove the plug from the wall outlet. A small amount of power
is always consumed while the power cord is connected to the wall
outlet.
To prevent the malfunction
• There are no user-servicable parts inside. If anything goes wrong,
unplug the power cord and consult your dealer.
• Do not insert any metallic objects, such as wires, hairpins, coins,
etc. into the unit.
• Do not block the vents. Blocking the vents may damage the unit.
To clean the cabinet
• Use a soft cloth. Follow the relevant instructions on the use of
chemically-coated cloths.
• Do not use benzene, thinner or other organic solvents and
disinfectants. These may cause deformation or discoloring.
Checking the supplied accessories
Check to be sure you have all of the following supplied accessories.
The number in parentheses indicates the quantity of each piece
supplied.
• Remote control (1)
• Batteries (2)
• AM loop antenna (1)
• FM antenna (1)
• Digital coaxial cord (1)
• Audio/video cord (1)
If anything is missing, contact your dealer immediately.
VOLTAGE SELECTOR
110V
127V
220V
230 -
240V
Voltage mark
EN01-08RX-ES1&XV-NK58[A]f 03.8.5, 17:195