Filter
Top Products
31
4
Adjust the surround speaker output levels
(from –10 dB to +10 dB).
• Make adjustments so that the sound level of the selected
speaker is set at the same level as that of the front speakers.
To adjust the left surround speaker level,
press SURR L +/–.
To adjust the right surround speaker level,
press SURR R +/–.
Ex.: When selecting “–8 (dB)” for “SURR R.”
5
Press TEST again to stop the test tone.
6
Only for DAP modes:
Press EFFECT to select the DAP effect level (1 to
5) you want.
• As the number increases, the DAP effect becomes stronger
(normally set it to “EFFECT 3”).
On the front panel:
• No test tone is available when using the buttons on the front panel.
Before you start, remember...
There is a time limit in doing the following steps. If the setting is
canceled before you finish, start from step
2
again.
1
Start playing 2 channel software—either Linear
PCM or analog signal—and select the source.
2
Press SURROUND.
MULTI JOG now works for the Surround/DSP mode selection.
3
Turn MULTI JOG until one of the DSP modes you
want to apply appears on the display.
The DSP indicator lights up on the display.
• As you turn MULTI JOG, the indication changes as follows:
4
Press ADJUST.
MULTI JOG now works for the sound adjustment.
STANDBY / ON STANDBY
DIMMER SETTING ADJUST SURROUND
DVD MULTI DVD DBS VCR TV FM / AM
SET / TUNER PRESET
SOURCE SELECTOR MASTER VOLUME
PHONES
/ MULTI JOG
SUBWFR
VOL
DSP
LR
LPCM
BASS
TREBLE
PANORAMA
B.BOOST
ATT
(Back to the beginning)
SUBWFR
SURR R
EFFECT*
SURR L
BAL
CENTER
5
Turn MULTI JOG until the setting item you want
to set appears on the display, then press SET.
• As you turn MULTI JOG, the indication changes as follows:
* Available only for DAP modes.
SURR L*
1
: To adjust the left surround speaker output level
(from –10 dB to +10 dB).
SURR R*
1
: To adjust the right surround speaker output level
(from –10 dB to +10 dB).
EFFECT (available only for DAP modes) *
2
:
To adjust the DAP effect level.
As the number increases, the effect becomes
stronger (normally set it to “EFFECT 3”).
*
1
“0 (dB)” is the initial setting for each speaker setting.
*
2
“3” is the initial setting.
6
Turn MULTI JOG to adjust the item selected in
step
5
, then press SET.
Your setting is stored.
• When adjusting the speaker output levels, make adjustments so
that the sound level of the selected speaker is set at the same
level as that of the front speakers.
Ex.: When selecting “–8 (dB)” for “SURR R.”
7
Repeat steps
5
and
6
to adjust the other
settings.
To cancel DSP Modes
Press SURROUND repeatedly on the remote control or press
SURROUND then turn MULTI JOG on the front panel so that
“STEREO” appears on the display. The DSP indicator goes off from
the display.
NOTES
• You can adjust the speaker output levels using the remote control
without outputting the test tone.
• You cannot adjust the center speaker output level and no test tone
comes out of the center speaker when “CNTR SP” is set to “NO.”
• You cannot adjust the surround speaker output levels and no test
tone comes out of the surround speakers when “SURR SP” is set
to “NO.”
SUBWFR
VOL
DSP
LR
LPCM
Creating realistic sound fields
SUBWFR
VOL
DSP
LR
LPCM
EFFECT 3
EFFECT 4
EFFECT 5
EFFECT 1
EFFECT 2
SUBWFR
VOL
DSP
LR
LPCM
SUBWFR
VOL
DSP
LR
LPCM
PLII MOVIE
PLII MUSIC
STEREO
(Surround/DSP off)
(Back to the beginning)
LIVE CLUB
PAVILION
HALL
DANCE CLUB
ALL CH ST.
EN26-32RX-ES1&XV-NK58[A]f 03.6.6, 11:5531