Filter
Top Products
9
Step 2: Setting Up
4th Step : Network Connection
Do you want to connect network connection?
It gives you network services that our AV
receiver support. If you wish to skip this step.
select “No. Skip”.
Yes
No. Skip
HOME Ex it
Initial Setup
Network Connection
You can check the network connection and make the Wi-
Fi setting. When the Network Connection start screen is
displayed, select "Yes" with the cursors and press Enter
on the remote controller. If you select "Wired" in the next
screen, you can view the LAN cable connection status. To
make the Wi-Fi setup, select "Wireless", press Enter on the
remote controller and follow the sections below.
Make the following preparations.
Wi-Fi connection requires an access point such as
wireless LAN router (). Write down the SSID and
password (key) of the access point if they are shown
in the label of the main body. If the access point has
an automatic setting button (may be called differently
according to the manufacturer), you can set up
without inputting the password. For how to use the
automatic setting button of the access point, refer to
its instruction manual.
The unit supports Wi-Fi connection with 2.4 GHz
access point.
1. Select the SSID of the access point to be connected
with the cursor buttons and press Enter.
When the SSID of the access point appears on the TV
screen, select the desired access point.
• If you changed the initial setting of the access point to
skip password entry, step 3 starts automatically.
• If you changed the initial setting of the access point
to hide the SSID, see "When the access point is not
displayed".
2. Select and set the authentication method.
Wi-Fi Setup
Select the authentication method.
Enter Password
Push Button
PIN code
When the screen above is displayed, select and set one
of the three authentication methods: "Enter Password",
"Push Button" and "PIN code". See below for details of
and how to set each method.
Enter Password: Enter the password of the access point to
establish connection.
1 Select "Enter Password" with the cursor buttons and
press Enter.
2 Enter the password () on the keyboard screen, select
"OK" with the cursor buttons and press Enter.
• The keyboard screen may be displayed automatically
if the access point device does not have an automatic
setting button.
Select "Shift" and press Enter to toggle between upper and lower
case. Select "
" or "
" and press Enter to move the cursor to the
selected direction. Select "Back Space" and press Enter to delete
the character at the left of the cursor position. To select whether to
mask the password with "" or display it in plain text, press D on the
remote control. Press + 10 on the remote controller to enable the
"Shift" function and CLR to delete all the input characters.
3 If the security method of the access point to be
connected is WEP, select "Default Key ID", select "OK"
and press Enter.
Push Button: Use the automatic setting button of the
access point to establish connection.
1 Select "Push Button" with the cursor buttons and press
Enter.
2 Hold down the automatic setting button of the access
point for the necessary seconds, select "OK" with the
cursor buttons and press Enter.
PIN code: Select this method when the automatic setting
button of the access point is beyond the reach. Select "PIN
code" with the cursor buttons and press Enter to display
the 8-digit PIN code. Register the displayed PIN code to the
access point, select "OK" with the cursor buttons and press
Enter. For how to register the PIN code to the access point,
refer to its instruction manual.
3. Establish connection.
The connection process starts and the Wi-Fi indicator
on the left of the unit's display starts flashing. When
connection has been established, the Wi-Fi indicator
changes from flashing to staying lit. If the Wi-Fi indicator
does not stay lit, connection has not been established.
Make the setting again. If "Push Button" does not work,
try "Enter Password".
When the access point is not displayed
Select "Other..." with the
c
cursor on the remote
controller and press Enter to display the keyboard
screen. Input the SSID and password. Make the
following settings according to the router setting.
WPA/WPA2 method
Select "WPA" or "WPA2" in "Security Method", select
"OK" and press Enter.
WEP method
Select "WEP" in "Security Method" and select
"Default Key ID". Then select "OK" and press Enter.
• If encryption setting has not been made on the
wireless LAN router, select "None" in "Security
Method", select "OK" and press Enter.
Exiting the setup wizard
After finishing the initial setup, keep "Finished" selected
and press Enter on the remote controller. Connection and
setting of the unit is now completed. See Step 3 and enjoy
your home theater.