Filter
Top Products
DOLBY SURROUND PRO LOGIC mode:
Choose this feature when playing Dolby Pro Logic
encoded movies and music (especially laser disc,
video tapes and TV broadcasts with Dolby Surround
sound). Most currently released video cassetles
and many TV broadcasts include this feature. Dolby
Pro Logic will not only give improved sound, it will
give a clear perception of the position and direction
of the original sound track.
Three types of centre mode are available when
using the Dolby Pro Logic feature, NORMAL WIDE
and PHANTOM. These options have programmed
surround (delay) values for the centre channel. The
delay (or echo effect) is different for each mode:
.The NORMAL mode gives true Dolby Pro Logic
sound.
.The WIDE mode can be used to gives greater
acoustic separation of the centre speaker-
.The PHANTOM mode diminishes the effect of
hearing a true centre channel. The main left and
right speakers give the effect of centre channel
information.
One other Pro Logic mode is available:
.The DOLBY 3 STEREO mode creates a Dolby
Pro Logic sound effect using just the left, right
and centre channels. No sound comes from the
surround channel speakers. You can still select
normal or wide effect in this mode.
you want to adjust, increase or decrease the volume
by holding the SPEAKER BALANCE + or -button
on the remote control. Let go when the balan~
sounds correct and the test noise cycle will continue
4. Press the TEST button again to stop the test
process.
Adjusting the surround sound balance while
playing a Pro Logic sound track
1.Select the desired audio (TUNER, CD, AUX'
TAPE)
2. Ensure that the Dolby Pro Logic is selected.
3.lf your source is Hi-Fi, VCR or laser disc player,
playa Dolby Pro Logic encoded video tape or
Dolby Pro Logic encoded laser disc. Make sure
your television's volume is turned down. Adjust
the MAIN volume buttons to a normal listening
level.
4.Using the remote control, press the SPEAKER
BALANCE button to light just the display symbol
for the speaker you wish to adjust.
5. Hold the SPEAKER BALANCE + button to
increase the volume or the SPEAKER BALANCE
-button to decrease the volume from the speaker
for which symbol is lit. Let go when the volume
sounds correct.
6. Wait about 10 seconds and the speaker display
symbols will go back to normal.
The following tables show which speakers are working in
the various modes.
To select and cancel Dolby Pro Logic modes
1.Press the PRO LOGIC. PHANTOM or DOLBY 3
STEREO button to select the required mode.
2. Press NORMAL or WIDE buttons to select normal
or wide effect (not available in phantom mode).
3. To cancel any Dolby Pro Logic mode. press the
PRESET EQUALIZER button.
Mode
ound
kers
.J
"
"
x
x
I NORMAL
PRO LOGIC
PHANTOM
~I
PRESET
EOUAllSER
x
Manufactured under license from Dolby Laboratories
Licensing Corporation.
NOTE:
It is not unusual on some Pro Logic material to have
little or no rear speaker output. This is normal and
to be expected, as part of the overall effect created
by the sound track producer.
To balance your Speakers for Surround sound:
Use the TEST button to set the correct balance of
sound between the LEFT, RIGHT, CENTRE and
SURROUND speakers in the Dolby Pro Logic mode.
DOLBY, the double-D symbol ID and "PRO LOGIC" are
trademarks of Dolby Laboratories Licensing Corporation.
(][) I DOLBY SURROUND I
p RO.LOG I C
NOTES: Ensure your speakers are correctly
positioned as shown on page E-4. " is recommended
to balance the speakers at a normal listening level.
1. With the unit switched on, press the TEST mode
button on the front panel or remote control.
2. You will hear a lest noise from the speakers which
will cycle from lefVright, centre and surround
speakers.
3. While Ihe tesl noise is coming from the speaker
E-8
-,-~'0".c"" :.0, ",*"