Filter
Top Products
ENGLISH
9
7
REMOTE CONTROL UNIT
2 The included remote control unit (RC-278) can be used to operate the DN-C550R from a distance.
q Remove the remote control unit’s back lid.
w Insert the two R6P (AA) batteries in the battery
compartment, in the direction indicated by the marks inside
the compartment.
e Put the back lid back on.
Cautions on batteries
• Use R6P (AA) batteries in the remote control unit.
• The batteries should be replaced with new ones after
approximately one year, though this depends on the
frequency with which the remote control unit is used.
• Even if the batteries are less than a year old, replace
them with new ones if the remote control unit no
longer operates even from a short distance from the
main unit.
• The included battery is only for verifying operation.
Replace it with a new battery as soon as possible.
• When inserting new batteries, wait about two
minutes after removing the old batteries before
inserting the new ones.
• Be sure to set the batteries in the proper “<” and
“>” directions, as indicated by the marks in the
remote control unit’s battery compartment.
• Remove the batteries when not using the remote
control unit for long periods of time.
• To avoid explosions and fluid leakage:
• Do not use one new battery with one old one.
• Do not use two different types of batteries.
• Do not short-circuit, disassemble, heat or dispose
of batteries in flames.
• If the battery fluid should leak, wipe all the fluid off
the battery compartment, then insert new batteries.
• When operating the remote control unit, point it at
the main unit as shown in the diagram.
• The remote control unit can be operated from a
direct distance of approximately 8 meters from
the main unit. This distance will be shortened,
however, if there are obstacles or when operated
from an angle.
(The remote control unit will operate from a
horizontal angle of up to about 30°.)
30°
30°
2
4
3
7
8
56
1
9
10
+
10
8
9
3
2
6
7
B
R
E
M
O
T
E
C
O
N
T
R
O
L
U
N
I
T
R
C
-
2
7
8
Using the remote control unit
Approx. 8 meters
NOTES:
• The remote control unit may not operate if the remote
sensor is exposed to direct sunlight or strong artificial
light, or if there is an obstacle between it and the remote
sensor.
• Do not press buttons on the main unit and on the remote
control unit at the same time. Doing so will result in
malfunction.
Inserting the batteries
STOP
PAU SE
PLAY
2
4
3
78
56
1
9
10
+
10
REC
_
DUBBING
_
NORMAL HIGH
RELAY
MODE
CD CD-R
ENTER
MENU
8
9
3
2
6
7
PROG/DIRECT
CALL
RANDOM
DISPLAY SEL
.
FADER INPUT FINALIZE
1 / ALL A - B
CHARACTER
TIME
TITLE
B
REMOTE CONTROL UNIT RC-278
M
+✽ –
CLEARCLEAR
A ! "A ! "
J
( )
D # %D # % G & 'G & '
P P
,
Y
< >
V V
:
;
S S
.
[ = ][ = ] {
?
}
Names and Functions of Remote Control Unit Buttons
2 Buttons not explained here function in the same way as the corresponding buttons on the main unit.
2 Buttons marked “✽” function regardless of the function selector switch.
Play button (1 PLAY)
Pause button (3 PAUSE)
Repeat A - B button (A - B)
Stop button (2 STOP)
Record button (4 REC)
Automatic search reverse
and forward buttons (
8
and 9)
Manual search reverse and
forward buttons (
6 and
7)
Random button (RANDOM)
Press this button to play the track
in random order.
(See Page 22.)
Display select button
(DISPLAY SEL.)
Press this to perform A-B repeat
playback.
Repeat 1/ALL button (1/ALL)
Press this to perform 1-track
repeat playback and all-track
repeat playback.
Character button
(CHARACTER)
Finalize button (FINALIZE)
Number buttons (1 to 10)
Use these buttons for direct
search and programmed playback.
Normal speed dubbing
mode button (DUBBING
NORMAL)
High speed dubbing
mode button (DUBBING
HIGH)
Relay mode button
(RELAY MODE)
Function selector
switch
+
10 button
Use this button to enter track
numbers of 11 or over for direct
search and programmed playback.
Call button (CALL)
Use this button to check the
programmed tracks.
Program/direct button
(PROG/DIRECT)
Press this button to switch
between the program setting
mode and the direct search mode.
Normally this is set to the direct
search mode.
Clear button (CLEAR)
Menu button (MENU)
Enter button (ENTER)
✽
✽
✽
✽
Switches the operation of
the buttons between the
CD and CD-R.
✽
✽
Title button (TITLE)
Press this button to switch the
time display to the title display.
Input select button (INPUT)
Time button (TIME)
Fader button (FADER)
Press this for fade-in and fade-out
recording.