Filter
Top Products
Getting Started Connections Playback Remote Control Multi-zone Information Troubleshooting
ENGLISH
Specifications
S1 Dynamic EQ
Audyssey Dynamic EQ solves the problem of deteriorating sound
quality as volume is decreased by taking into account human perception
and room acoustics. Audyssey Dynamic EQ works in tandem with
Audyssey MultEQ to provide well-balanced sound for every listener
at any volume level.
NOTE
• “Dynamic EQ” can only be set when auto setup has been
performed.
• “Dynamic EQ” cannot be set in the following situations.
•
If “Auto Setup” fails to be completed.
•
After running Auto Setup, when the number of used speakers has
increased from the number of measured speakers.
• When “MultEQ” is set to “OFF”, “Dynamic EQ” is automatically set
to “OFF”.
• When you set ”Dynamic EQ” to ”ON”, “Tone Control” and “Night
Mode” are switched ”OFF”.
[Selectable items]
ON
: Use Dynamic EQ function.
OFF
: Do not use Dynamic EQ function.
Operating from the main unit or remote control
unit
Press DYNAMIC VOLUME.
Dynamic EQ / Volume : ON Dynamic EQ : ON / Volume : OFF
Dynamic EQ / Volume : OFF
Before running Auto Setup and after running Auto Setup, if the number
of speakers has increased or you pressed DYNAMIC VOLUME, “Run
Audyssey” is displayed. In this case, either perform Auto Setup again,
or return to the setting after running Auto Setup with “Auto Setup”
– “Parameter Check” – “Restore”.
n Operating conditions for each function
• Dynamic EQ : When “MultEQ” is set to “ON”
• Dynamic Volume : When “Dynamic EQ” is set to “ON”
• Setting : When “Dynamic Volume” is set to “ON”
S0 MultEQ
S1 Dynamic EQ
S2 Dynamic Volume
S3 Setting
S2 Dynamic Volume
Audyssey Dynamic Volume solves the problem of large variations in
volume level between television programs, commercials, and between
the soft and loud passages of movies.
Audyssey Dynamic EQ is integrated into Dynamic Volume so that as
the playback volume is adjusted automatically, the perceived bass
response, tonal balance, surround impression, and dialog clarity
remain the same.
NOTE
• “Dynamic Volume” can only be set when auto setup has been
performed.
• “Dynamic Volume” cannot be set in the following situations.
•
If “Auto Setup” fails to be completed.
•
After running Auto Setup, when the number of used speakers has
increased from the number of measured speakers.
• When “MultEQ” is set to “OFF”, “Dynamic Volume” is automatically
set to “OFF”.
• “Dynamic Volume” and “Night Mode” cannot be used jointly.
[Selectable items]
ON
: Use Dynamic Volume.
The Dynamic Volume effect will be at the level of the
“Setting”.
OFF
: Do not use Dynamic Volume.
Before running Auto Setup and after running Auto Setup, if the number
of speakers has increased or you pressed DYNAMIC VOLUME, “Run
Audyssey” is displayed. In this case, either perform Auto Setup again,
or return to the setting after running Auto Setup with “Auto Setup”
– “Parameter Check” – “Restore”.
Operating from the main unit or remote control
unit
Press DYNAMIC VOLUME.
Dynamic EQ / Volume : ON
“Green” “Red”
Dynamic EQ : ON / Volume : OFF
Dynamic EQ / Volume : OFF
S3 Setting (Dynamic Volume Setting)
Can be set when “Dynamic Volume” is set to “ON”.
Set Dynamic Volume effect.
[Selectable items]
Midnight
: High setting affects volume the most, causing all sounds
to be of equal loudness.
Evening
: Middle setting prevents loud and soft sounds from
being much louder and softer respectively than average
sounds.
Day
: Low setting provides the least adjustments to the
loudest and softest of sounds.
NOTE
• “Setting” can only be set when auto setup has been performed.
• “Setting” cannot be set in the following situations.
•
If “Auto Setup” fails to be completed.
•
After running Auto Setup, when the number of used speakers has
increased from the number of measured speakers.
•
If “Dynamic Volume” setting is “OFF”.
About Dynamic Volume
Audyssey Dynamic Volume™ solves the problem of large variations
in volume level between television programs, commercials, and
between the soft and loud passages of movies.
Dynamic Volume looks at the preferred volume setting by the user and
then monitors how the volume of program material is being perceived
by listeners in real time to decide whether an adjustment is needed.
Whenever necessary, Dynamic Volume makes the necessary rapid
or gradual adjustments to maintain the desired playback volume
level while optimizing the dynamic range. Audyssey Dynamic EQ is
integrated into Dynamic Volume so that as the playback volume is
adjusted automatically, the perceived bass response, tonal balance,
surround impression, and dialog clarity remain the same whether
watching movies, flipping between television channels, or changing
from stereo to surround sound content.
About Dynamic EQ
Audyssey Dynamic EQ™ solves the problem of deteriorating sound
quality as volume is decreased by taking into account human
perception and room acoustics. Dynamic EQ selects the correct
frequency response and surround levels moment-by-moment at
any user-selected volume setting. The result is bass response,
tonal balance, and surround impression that remain constant
despite changes in volume. Dynamic EQ combines information
from incoming source levels with actual output sound levels in the
room, a prerequisite for delivering a loudness correction solution.
Audyssey Dynamic EQ works in tandem with Audyssey MultEQ to
provide well-balanced sound for every listener at any volume level.
For details on adjusting individual parameters, see “Adjusting the parameters” (vpage 42).
Getting Started Connections Playback Remote Control Multi-zone Information Troubleshooting
ENGLISH
Setup