Filter
Top Products
9-EN
RESET switch
1
2
Compatibility with Factory Steering Wheel Radio
Controls
If your vehicle has steering wheel controls for the radio,
an optional steering wheel control interface may be
available to connect to your Alpine radio. For details,
contact your Alpine dealer.
Turning Power On or Off
Some of this unit's functions cannot be performed while the vehicle is
in motion. Be sure to stop your vehicle in a safe location and apply the
parking brake, before attempting these operations.
1
Press SOURCE/POWER to turn on the unit.
The opening screen appears automatically.
•
The unit can be turned on by pressing any button on the unit
except the FLAT/SLIDE, OPEN/CLOSE , TILT
and
c (Eject).
2
Press and hold SOURCE/POWER for at least 2
seconds to turn off the unit.
• The IVA-D900 draws minimal current even when its power switch
is turned off. If the switched power (ignition) lead of the IVA-D900
is connected directly to the positive (+) post of the vehicle's battery,
the battery may be discharged. If this lead is unswitched, it must be
disconnected from the battery post should the vehicle be left unused
for an extended period of time.
An SPST (Single-Pole, Single-Throw) switch (sold separately) can
be added to simplify this procedure. Then, you can simply place it
in the OFF position when you leave the vehicle. Turn the SPST
switch back ON before using the IVA-D900. For connecting the
SPST switch, refer to the "Connection Diagram of SPST switch"
(page 70).
• Some operation of the unit cannot be performed while the vehicle is
in motion. In this case, be sure to first stop your vehicle and apply
the parking brake, then perform the operation.
Detaching and Attaching the Front Panel
Detaching
1
Turn off the unit power.
2
Press (Release) at the lower right side until the
front panel pops out.
3
Grasp the right side of the front panel, lift it up
slightly then pull it out.
• The front panel may become hot in normal usage (especially the
connector terminals on the back of the front panel.) This is not a
malfunction.
• To protect the front panel, place it in the supplied carrying case.
Attaching
1
Insert the left side of the front panel into the main
unit. Align the groove on the front panel with the
projections on the main unit.
2
Push the right side of the front panel until it locks
firmly into the main unit.
• Before attaching the front panel, make sure that there is no dirt or
dust on the connector terminals and no foreign object between the
front panel and the main unit.
• Attach the front panel carefully, holding the sides of the front panel
to avoid pushing buttons by mistake.
Initial System Start-Up
Immediately after installing or applying power to the unit, it should be
initialized. To do this, first, remove the detachable front panel. Behind
the front panel, to the left of the connector, there is a small hole.
Using a pencil or other pointed object, press the reset switch mounted
behind this hole to complete the initialization procedure.
• Any of the buttons does not function while the monitor is closing by
reset.
Raising/Lowering the Monitor
Press OPEN/CLOSE.
The unit beeps 3 times and raises (or lowers) the monitor
automatically.
• The IVA-D900 is a precision device. With gentle handling, its
unique capabilities can be enjoyed for a long time.
• If the monitor touches an obstacle while it is being raised (or
lowered), the unit will stop raising (or lowering) the monitor
immediately. Should this occur, remove the obstacle and press
OPEN/CLOSE again to lower the monitor.
• When the movable monitor is opened, do not place any object on
the monitor and be careful not to bump or apply any pressure to
the monitor while it is open. This can cause damage to the
mechanism.
• In low ambient temperature conditions, the display may be dark for
a short period of time immediately after the power is turned on.
Once the LCD has warmed up, the display returns to normal.
• For your safety, some operation of the unit cannot be performed
while the vehicle is in motion. In this case, first stop the vehicle
and engage the parking brake, then perform the operation.
• Operation of the remote control (pages 52-55) can be carried out
even while the monitor screen is closed.