Filter
Top Products
E-15
English
1
1
2
2
3
3
4
4
5
5
+I0
E
6
6
7
7
8
8
9 0
VCD/CD
PRESET
TIME
A
PROG
B C D
+I0
E
VCD/CD
1
1
2
2
3
3
4
4
5
5
6
6
7
7
8
8
9 0
PRESET
INPUT
TIME INDEX
INTRO DIGEST
POWER
DISPLAY
SLEEP
MUSIC
FLAT
PROGRAM
USER
VOLUME
DISC SKIP
RETURN
PREV NEXT
SELECT
LEVEL
TEST
CENTER/REAR
/DELAY
ECHO/
KEY
OPEN/CLOSE
INDEXMODE
TUNER
VIDEO CD PLAYER OPERATION
Direct operation
When this unit is in the standby mode, pressing the DISC
selector (1, 2 or 3) button will turn the power on and start disc
playback automatically.
When the power is on, even if an input source other than
Video CD player is selected, pressing a DISC selector button
or closing the disc table by pushing the front edge of the disc
table gently will start playback directly.
* These ways of playback can also be used to close the disc
table. If the table is closed in these ways, playback will
begin automatically, however, the display will not show the
total number of tracks and the total playing time of the disc
to be played back.
PLAYXCHANGE
During playback, you can open the disc table by pressing the
DISC CHANGE button without interrupting playback.
However, in this state, pressing the DISC SKIP button or a
DISC selector button has no effect.
Precautions
•
If TV or radio interference occurs during Video CD player
operation, move the unit away from the TV or radio.
•
Subjecting the unit to shock or vibration can cause
mistracking.
•
Playing back some discs at high volume can cause
mistracking. In this case, listen at lower volume.
•
Do not pull open the disc table forcibly with your hands.
•
Do not push the disc table while it is moving.
•
If the power fails while the table is open, wait until the
power supply returns or gently push the table manually to
close it.
•
The temperature range for playing back discs is
recommended to be 5°C (41°F) – 35°C (95°F).
Direct-selection playback
By using the track number input buttons on the remote
control transmitter, any track you wish to listen to can be
played back directly.
Use the track number input buttons to select the desired
track number. Playback will begin automatically.
A. For example, to choose selection 5
Press the “5” button.
B. For example, to choose selection 12
(1)Press the “+10” button.
(2)Within 3 seconds, press “2” button.
C. For example, to choose selection 20
(1)Press the “+10” button.
(2)Within 3 seconds, press the “+10” button again.
(3)Within 3 seconds, press the “0” button.
Note
If you select a track number higher than the number of tracks
on the disc, playback will begin from the last track on the
disc.
For easier operation
Pressing the DISC selector button (1, 2 or 3) will select the
disc directly, and playback will begin from track 1
automatically.
Note
If a Video CD, version 2.0 is selected, “PBC” lights up on the
display, and the total number of tracks, the total playing time
of the disc and the music calendar will not be displayed. In
this mode, disc playback is controlled by the rule of Playback
Control. (For details of Playback Control, refer to page
22–24.)
To cancel this mode and restore the normal playback mode,
press the stop (RETURN) button. “PBC” disappears from
the display.
To call the Playback Control mode again, press and hold the
stop (RETURN) button for more than 2 seconds.
To interrupt playback
1 Press the play/pause / button.
* The “ ” indicator will flash.
2 Press the play/pause / button to resume playback
from the same point.
To stop playback
Press the stop button.
To switch the unit in the standby mode after use
Turn the unit into the standby mode by pressing the POWER
switch. (The indicators will go off except for the current time
display.)