Filter
Top Products
masterpage:Left
lename[E:\SEM_Janet\Revision
D
ata\J9051275_2598516131DB798CEL\2598516131\GB06ADV_STR-DB798-CEL.fm]
40
GB
model name1[STR-DB798]
[2-598-516-13(1)]
Using the CUSTOMIZE menu
to adjust the receiver
You can adjust various receiver settings using
the CUSTOMIZE menu.
1 Press MAIN MENU repeatedly to select
“CUSTOM”.
2 Turn MENU to select the parameter you
want to adjust.
For details, see “CUSTOMIZE menu
parameters” below.
3 Turn –/+ to select the setting you want.
The setting is entered automatically.
4 Repeat steps 2 and 3 to adjust the other
items.
CUSTOMIZE menu parameters
The initial setting is underlined.
xMENU XXX (Menu expanding)
•EXP.
The advanced parameters for the SPEAKER SETUP
and LEVEL menus are displayed and can be
adjusted. For details on each setup item, see pages
17, 38 and the following pages.
•STD
The advanced parameters for SPEAKER SETUP and
LEVEL menus are not displayed.
x 96 XXXX
(DTS 96/24 decoding mode)
• AUTO
When a DTS 96/24 signal is input, it is played back
at 96 kHz sampling frequencies.
•OFF
Even when a DTS 96/24 signal is input, it is played
back at 48 kHz sampling frequencies.
Notes
• This parameter is valid only in A.F.D. mode
(page 31). In other sound fields, this parameter is
automatically set to “OFF”.
• Even when a DTS 96/24 signal is input, standard 48
kHz decoding is used if any speakers are set to
“SMALL” or if the sub woofer is set to “NO”.
xSB XXXX
(Surround back decoding mode)
You can also press SURR BACK DECODING to
select the surround back decoding mode (page 35).
For details on each decoding mode, see page 36.
•OFF
• AUTO
•ON
Note
This parameter is valid only when A.F.D. mode is
selected except for Dolby Pro Logic IIx mode
(page 31).
xS.F XXXX (Sound field link)
•LINK
Lets you apply the last selected sound field to an
input whenever it is selected. For example, if you
select HALL for the SA-CD/CD input, then change
to a different input and return to SA-CD/CD, HALL
will automatically be applied again.
•FIX
Sound field link is not activated.
xA.V.SYNC.XX
(Time alignment)
Initial setting: 0 (0 ms)
Let you delay the output of audio to adjust the gap
between video and audio. You can adjust from 0 (0 ms)
to 20 (200 ms) in 10 ms steps.
xDEC. XXXX
(Digital audio input decoding priority)
Lets you specify the input mode for the digital signal
input to the DIGITAL IN jacks.
The initial setting is “DEC. AUTO” for VIDEO 3 and
TV/SAT, and “DEC. PCM” for DVD, MD/TAPE and
SA-CD/CD.
• AUTO
Automatically switches the input mode between
DTS, Dolby Digital, or PCM.
•PCM
PCM signals are given priority (to prevent the
interruption when playback starts). Even when other
signals are input, the sound is output. However, this
receiver cannot decode DTS-CD when set to “DEC.
PCM”.
Note
When set to “DEC. AUTO” and the sound from the
digital audio jacks (for SA-CD/CD, etc.) is interrupted
when playback starts, set to “DEC. PCM”.
Advanced settings
DTS 96/24
GB01COV_STR-DB798-CEL.book Page 40 Thursday, August 18, 2005 8:59 AM