Filter
Top Products
3-859-278-11(1)
Additional Information
32
EN
Specifications
Recording section
Tape Digital audio tape
Recording head Rotary head
Recording time Standard: 120 minutes
Long-play: 240 minutes
(DT-120)
Tape speed Standard: 8.15 mm/s
Long-play: 4.075 mm/s
Drum rotation Standard: 2,000 rpm
Long-play: 1,000 rpm
Error correction Double-encoded Reed Solomon code
Tape section
Track pitch 13.6 µm (20.4 µm)
Sampling frequency 48 kHz, 44.1 kHz, 32 kHz
Modulation system 8-10 modulation
Transfer rate 2.46 Mbit/sec
Number of channels 2 channels, stereo
D / A conversion Standard: 16-bit linear
(quantization) Long-play: 12-bit non-linear
General section
Power requirements
Where purchased Power requirements
U.S.A./Canada 120 V AC, 60 Hz
Europe/U.K 230 V AC, 50/60 Hz
Power consumption PCM-R500: 34W
PCM-R700: 34W
Dimensions Approx 482 × 145 × 355 mm (w/h/d)
(19 × 5
3
/4 × 14 inches)
(not including rack mount adaptor)
Weight PCM-R500: Approx 7.2kg (15 lb 14 oz)
PCM-R700: Approx 7.3kg (16 lb 2 oz)
Remote commander RM-D757 (supplied)
Remote control system Infrared control
Power requirements 3V DC, with two size-AA (R6) batteries
Dimensions Approx 45 × 210 × 26 mm (w/h/d)
(1
13
/16 × 8
3
/8 × 1
1
/16 inches)
Weight Approx 100g (3.5 oz) incl. batteries
Input connectors
Analog Input
Digital Input
Connector Type Input impedance Rated input level
AES/EBU
COAXIAL
XLR-3
(FEMALE)
—
Phono-plug
jack
75 ohms
0.5 Vp-p
Output connectors
Analog Output
ANALOG
(BALANCE)
Connector Load
impedance
32 ohms
Digital Output
Connector Load
impedance
Output
impedance
Type
AES/EBU
110 ohms
COAXIAL
75 ohms
75 ohmsPhono-plug
jack
XLR-3
(MALE)
35 ohms
(balanced)
Rated
output
level
0.5 Vp-p
—
Variable range of analog (BALANCE) input/output reference level
a)
+4 dBs to –12 dBs
Maximum analog (BALANCE) output level
+24 dBs
Remote switch connectors DIN connector (8-pin, parallel)
Monaural minijack (serial)
Audio characteristics
Frequency response
b)
Standard: 20-20,000 Hz (±0.5 dB)
Long-play: 20-14,500 Hz (±0.5 dB)
Signal-to-noise ratio
b)
90 dB or more (20 kHz LPF, A-
Weight filter ON)
Total harmonic distortion
b)
Standard: 0.05% or less
Long-play: 0.3% or less
(1 kHz, Reference level
a)
20 kHz
LPF ON)
Wow and flutter Below measurable limit (±0.001%
W.PEAK)
a)The reference level corresponds to –20 dB on the peak
level meters.
b)During analog input with the SBM function off
Supplied accessories See page 4.
Design and specifications are subject to change without
notice.
PHONES
XLR-3
(MALE)
Rated
output
level
a)
Output
impedance
Type
Stereo phone-
plug jack
100 ohms 0.36 mW
Phono-plug
jack
1 kilohm –12 dBs 47 kilohms
ANALOG
(UNBALANCE)
110 ohms
(balanced)
+4 dBs
(factory
setting)
100 ohms
(balanced)
10 kilohms
or more
Connector Type Input impedance Rated input level
a)
ANALOG
(UNBALANCE)
ANALOG
(BALANCE)
Phono-
plug jack
XLR-3
(FEMALE)
47 kilohms
10 kilohms
or more
(balanced)
–12 dBs
+4 dBs
(factory setting)