Filter
Top Products
EENNGGLLIISSHH
18
In the Dolby Digital mode, the optimum performance of
your system occurs when the sound from all five speakers
arrives at your primary listening position at the time. If all
speakers are equidistant from the main listening position,
set the following delay.
Center delay time: 0 ms, Rear delay time: 0 ms
If the center speaker is closer to your prime listening
position than the average distance to the left and right
main speakers add 1 ms of center channel delay for
each foot of difference.
The maximum is 5 ms.
If the surround speakers are closer to your main
listening position than the main left and right speakers,
add 5 ms of surround channel delay for each 5 feet of
difference. The maximum is 15 ms.
In Dolby Pro Logic, if the surround speakers are the
same distance from your primary listening position as
your main left and right front speakers, set the Rear Delay
time at 15 ms.
If the surround speakers are closer to your main listening
position than the main left and right speakers, your
receiver allows you to optimize the arrival time of the
sound from your speakers. Measure the distance from the
prime listening position to each of the speakers to the
nearest foot.
Add 5 ms of surround channel delay for each 5 feet of
difference. The maximum is 30 ms.
AAddjjuussttiinngg eeaacchh cchhaannnneell lleevveell wwiitthh tteesstt ttoonnee
AAddjjuussttiinngg ddeellaayy ttiimmeess ooff tthhee ssppeeaakkeerrss iinn DDoollbbyy
DDiiggiittaall,, DDoollbbyy PPrroo LLooggiicc oorr DDoollbbyy VViirrttuuaall mmooddee
Enter the test tone mode.
10
Repeat the steps 7 to 9 in “Adjusting
each channel level” until the sound level
of each speaker is heard to be equally
loud.
11
Cancel the test tone function.
12
In the surround modes only, the volume level of
each channel can be adjusted easily with the test
tone function.
Note: When “IN-DTS” is selected or the 6 CH DIRECT
is selected as an input source, the test tone
function does not work.
The test tone will be heard from the speaker of each
channel for 2 seconds as follows;
Front Left Center Front Right
SUBwoofer Rear Left Rear Right
When the speaker setting is “N”, the test tone of the
corresponding channel is not available.
POWER P.SCAN
DECK
DISPLAY
SLEEP
T.TO N E
D.TIME
ADJUST
AUTO DSP MODE
12345
67890
STEREO
A
B
SYS
CD
ENTEROSD
INTROREPEAT
DISC
A B
<
<
CD
TUNERVIDEO
PRESET
USERFILET.MONDISPLAY
AUX
TAPE MON.
EQUALIZER
INPUT
SELECTOR
6CH DIRECT
CH LEVEL MASTER
MUTE
CH SEL.
DECK SEL.
T.TONE
POWER P.SCAN
DECK
DISPLAY
SLEEP
T.TONE
D.TIME
ADJUST
AUTO DSP MODE
12345
67890
STEREO
A
B
SYS
CD
ENTEROSD
INTROREPEAT
DISC
A B
<
<
CD
TUNERVIDEO
PRESET
USERFILET.MONDISPLAY
AUX
TAPE MON.
EQUALIZER
INPUT
SELECTOR
6CH DIRECT
CH LEVEL MASTER
MUTE
CH SEL.
DECK SEL.
T.TONE
Check the current delay time.
13
The current delay time will be displayed for 5
seconds.
In the Dolby Digital mode, only, the center delay is
adjustable and the corresponding delay time is also
displayed.
In the Dolby Virtual mode, “NARROW” or “WIDE”
is displayed.
POWER P.SCAN
DECK
DISPLAY
SLEEP
T.TO N E
D.TIME
ADJUST
AUTO DSP MODE
12345
67890
STEREO
A
B
SYS
CD
ENTEROSD
INTROREPEAT
DISC
A B
<
<
CD
TUNERVIDEO
PRESET
USERFILET.MONDISPLAY
AUX
TAPE MON.
EQUALIZER
INPUT
SELECTOR
6CH DIRECT
CH LEVEL MASTER
MUTE
CH SEL.
DECK SEL.
D.TIME