Filter
Top Products
EENNGGLLIISSHH
16
ENJOYING SURROUND SOUND
Surround sound effect will not work properly if the signal passes through a graphic equalizer.
Please refer to your equalizer operating instructions for guidance on switching off (or defeating) the equalizer.
Select the desired surround mode.
When selecting a digital input for DTS,
Dolby Digital, etc.
1
Each time the AUTO button is pressed, the surround
mode changes as follows:
IN-AUTO:
When selecting DTS, Dolby Digital or Dolby Pro Logic
mode automatically according to the digital signal input.
IN-DTS : When playing DTS program sources only.
IN-PCM : When playing stereo program sources such as CD,
television, etc.
When “IN-DTS” or “IN-PCM” is selected, the
LOCK indicator lights up.
If the surround mode does not match the digital
signal input, no sound may be heard.
When the analog input is selected, the AUTO button
cannot be activated.
When selecting a surround mode among Dolby Pro
Logic, Dolby Virtual, Circle Surround, Theater, Hall
and Stadium modes.
Each time the DSP MODE button is pressed, the
surround mode changes as follows;
DOLBY PRO LOGIC DOLBY VIRTUAL CIRCLE SURROUND
STADIUM HALL THEATER
When “IN-PCM” is selected, these surround modes
can be also selected with the DSP MODE button.
When the Dolby Digital mode is selected automatically
in “IN-AUTO” mode, each time the DSP MODE button
is pressed, the surround mode changes as follows;
DOLBY DIGITAL DOLBY VIRTUAL
When playing Dolby Digital 2.0 program sources in
the “IN-AUTO” mode, either Dolby Pro Logic or
Dolby Digital will be selected automatically based on
the encoded signal. In this case, each time the DSP
MODE button is pressed, the surround mode changes
as follows;
(DOLBY DIGITAL) DOLBY PRO LOGIC DOLBY VIRTUAL
( ): The availability of Dolby Digital depens on program encoding.
This receiver is equipped with circuitry that allows the use of a
wide range of speaker systems.
This circuitry works be redirecting the bass frequencies or the
entire channel to speakers that are capable of reproducing them.
When a large or full range speaker capable of deep bass
response is used for one of the channels, that channel should be
set to L.
When a small or satellite speaker with limited bass capability is
used, that channel should be set to S. Deep bass from that
channel will be redirected to the main left and right speakers or
to the subwoofer.
When there is no speaker available, that channel should be set
to N. All the information in that channel will be redirected to
other available speakers.
When canceling the surround mode for normal
stereo operation.
POWER P.SCAN
DECK
DISPLAY
SLEEP
T.TONE
D.TIME
ADJUST
AUTO DSP MODE
12345
67890
STEREO
A
B
SYS
CD
ENTEROSD
INTROREPEAT
DISC
A B
<
<
CD
TUNERVIDEO
PRESET
USERFILET.MONDISPLAY
AUX
TAPE MON.
EQUALIZER
INPUT
SELECTOR
6CH DIRECT
CH LEVEL MASTER
MUTE
CH SEL.
DECK SEL.
or
AUTO
AUTO
POWER P.SCAN
DECK
DISPLAY
SLEEP
T.TO N E
D.TIME
ADJUST
AUTO DSP MODE
12345
67890
STEREO
A
B
SYS
CD
ENTEROSD
INTROREPEAT
DISC
A B
<
<
CD
TUNERVIDEO
PRESET
USERFILET.MONDISPLAY
AUX
TAPE MON.
EQUALIZER
INPUT
SELECTOR
6CH DIRECT
CH LEVEL MASTER
MUTE
CH SEL.
DECK SEL.
or
DSP MODE
DSP MODE
POWER P.SCAN
DECK
DISPLAY
SLEEP
T.TO N E
D.TIME
ADJUST
AUTO DSP MODE
12345
67890
STEREO
A
B
SYS
CD
ENTEROSD
INTROREPEAT
DISC
A B
<
<
CD
TUNERVIDEO
PRESET
USERFILET.MONDISPLAY
AUX
TAPE MON.
EQUALIZER
INPUT
SELECTOR
6CH DIRECT
CH LEVEL MASTER
MUTE
CH SEL.
DECK SEL.
or
STEREO
STEREO
AAddjjuussttiinngg tthhee ssppeeaakkeerr sseettttiinnggss
With the receiver in any of the surround
modes, press the SPEAKER MODE
button for more than 2 seconds to enter
the front-center-rear speaker set-up mode.
2
The existing front-rear-center speaker setting is displayed.
This set-up mode is not available when 6 CH DIRECT is
selected the input source or when ANALOG is selected as the
signal input in the STEREO mode.
Each time this button is pressed, one of 11 different
speaker settings is selected and displayed for 8 seconds as
follows;
FL--CS--RS, FL--CL--RS, FL--CL--RL,
FL--CL--RN, FL--CS--RL, FL--CN--RL,
FL--CS--RN, FL--CN--RS, FS--CS--RS,
FS--CS--RN, and FS--CN--RS
F stands for Front Speakers, C for Center Speaker, R for
Rear Speakers, L for Large, S for Small and N for None.
Large Speakers are capable of deep bass response and
typically have one driver with a cone that is 10(25 cm) or
larger.
The following speaker settings cannot be selected.
FS--CL--RL or CN--RN.
Select the desired speaker
setting.
3
SPEAKER
MODE
ADJUST