Filter
Top Products
11
LISTENING TO A PROGRAM SOURCE
OOppeerraattiioonnss
BBeeffoorree ooppeerraattiioonn
Select the desired input source.
3
Enter the standby mode.
The STANDBY button lights up in red.
This means that the receiver is connected to the AC
power and a small amount of current is retained to
support the memorized contents and operational
readiness.
To switch the power completely off, push the
POWER switch, again.
The power is cut off and the STANDBY light goes
off.
Each time the STANDBY button on the front panel or
the POWER button on the remote control is pressed,
the receiver turns on to enter the operating mode(the
STANDBY button lights up in green) or turns off to
enter the standby mode(the STANDBY button lights
up in red).
In the standby mode, if one of the INPUT SELECTOR
buttons is pressed, the receiver is turned on
automatically and the desired input is selected.
The SPEAKER indicator lights up and sound can be
heard from the speakers connected to the speaker
terminals.
When using headphones for private listening, press the
SPEAKER button again to switch the speakers off.
Each time the “AUDIO” button is pressed, the input
source changes as follows;
TUNER CD AUX
(frequency display)
Each time the “VIDEO” button is pressed, the input
source changes as follows;
VIDEO 1 VIDEO 2 VIDEO 3 VIDEO 4
When the TAPE MONITOR button is set to on so that
“TAPE M” indicator lights up, other inputs can not be
heard from the speakers.
To listen to an input source other than TAPE MONITOR,
be sure to set the TAPE MONITOR button to off.
TAPE MONITOR function
You can connect either a tape deck or a graphic equalizer
to the receiver’s TAPE MONITOR jacks.
To listen to the component connected to these jacks, set the
TAPE MONITOR button to on.
If you connect a 3-head tape deck, you can monitor the
actual recording while it is in progress and not just the
source sound.
For further details, refer to the operating instructions of
the component connected.
When selecting the 6 CH DIRECT as desired
6-DIRECT is displayed and the 6 separate analog
signals from a decoder or DVD player connected to
this unit will be heard. You can use the tone controls
and volume control to adjust the signal. (If the TAPE
MONITOR button is set to on, it will be automatically
set to off.)
To cancel the 6 CH DIRECT function, press the 6 CH
DIRECT button again or select another desired input
source.
These 6 separate analog signals can be heard, only.
They cannot be recorded.
In the standby mode, turn the power on.
1
EENNGGLLIISSHH
MAIN POWER
ON/ OFF
or
INPUT SELECTOR
AUDIO
VIDEO TAPE MON.
POWER P.SCAN
DECK
DISPLAY
SLEEP
T.TONE
D.TIME
ADJUST
AUTO DSP MODE
12345
67890
STEREO
A
B
SYS
CD
ENTEROSD
INTROREPEAT
DISC
A B
<
<
CD
TUNERVIDEO
PRESET
USERFILET.MONDISPLAY
AUX
TAPE MON.
EQUALIZER
INPUT
SELECTOR
6CH DIRECT
CH LEVEL MASTER
MUTE
CH SEL.
DECK SEL.
CD
TUNER VIDEO
AUX
TAPE MON.
POWER P.SCAN
DECK
DISPLAY
SLEEP
T.TO N E
D.TIME
ADJUST
AUTO DSP MODE
12345
67890
STEREO
A
B
SYS
CD
ENTEROSD
INTROREPEAT
DISC
A B
<
<
CD
TUNERVIDEO
PRESET
USERFI LET.MONDISPLAY
AUX
TAPE MON.
EQUALIZER
INPUT
SELECTOR
6CH DIRECT
CH LEVEL MASTER
MUTE
CH SEL.
DECK SEL.
or
ON/STANDBY
STANDBY
POWER
ON/OFF
SPEAKER
POWER P.SCAN
DECK
DISPLAY
SLEEP
T.TONE
D.TIME
ADJUST
AUTO DSP MODE
12345
67890
STEREO
A
B
SYS
CD
ENTEROSD
INTROREPEAT
DISC
A B
<
<
CD
TUNERVIDEO
PRESET
USERFILET.MONDISPLAY
AUX
TAPE MON.
EQUALIZER
INPUT
SELECTOR
6CH DIRECT
CH LEVEL MASTER
MUTE
CH SEL.
DECK SEL.
or
6CH DIRECT
6CH DIRECT
Switch the speakers on.
2