Filter
Top Products
21
To cancel the surround mode for stereo operation
• Depending on the signal format which is being input, either the stereo
mode or the 2CH downmix mode is selected.
• To cancel either the stereo mode or the 2CH downmix mode, select
the surround mode with using the MULTI CONTROL knob on the front
panel or the SURROUND MODE UP/DOWN ( >/< ) buttons on the
remote control.
2CH downmix mode
• This mode allows the multi-channel signals encoded in DTS or Dolby Digital format to be mixed down into 2 front channels and
to be reproduced through only two front speakers or through headphones.
• When the SPEAKER button is set to off to listen with headphones, if the STEREO button is pressed while playing the multi-
channel digital signals from DTS or Dolby Digital sources, it will enter the 2CH downmix mode automatically.
• To cancel the 2CH downmix mode, select the desired Dolby Headphone mode with using the MULTI CONTROL knob on the
front panel or the SURROUND MODE UP/DOWN ( >/< ) buttons on the remote control.
• The Dolby Headphone function simulates 5.1 channel surround sound, which allows you to enjoy 5.1 channel surround sound
through 2 channel headphones, just like listening from 5.1 channel speakers.
Notes :
• Only when the SPEAKER button is set to off, the Dolby Headphone mode can be selected.
• When playing the 96 kHz PCM(2 channel) digital signals, only the stereo mode can be selected.
• While listening with headphones, select the desired Dolby Headphone mode.
• Each time the MULTI CONTROL knob is rotated or the SURROUND
MODE UP/DOWN ( >/< ) buttons are pressed, the mode changes as
follows :
DH 1 : This simulates the soundfield as if you were in a relatively small room
with less reverberations.
DH 2 : This simulates the soundfield as if you were in a typical listening room
with moderate reverberations.
DH 3 : This simulates the soundfield as if you were in a large space like
theater.
• Depending on the kind of digital input signal or/and the selected
surround mode, the corresponding parameter mode is displayed
for several seconds as follows:
* “NIGHT” (Night mode) :
Selectable only while playing digital signals from Dolby Digital or DTS
source.
* “PANO” (Panorama mode) :
Selectable only while listening in Dolby Pro Logic II/Dolby Pro Logic IIx
Music mode.
* “REF” or “WIDE” (Dolby VS Reference/Wide mode) :
Selectable only while listening in Dolby Virtual Speaker mode.
* “DH 1” (Dolby Headphone 1 mode) :
Selectable only while listening in Dolby Headphone mode.
• If the parameter mode disappears, press this button again.
Listening in a Dolby Headphone mode
DISPLAY
SEL SEL
SETUP
TONE
SOUND
PARAMETER
REMOTE CONTROL RC-110
ENTER
VIDEO 1TAPE VIDEO 2VIDEO 3
EXT.IN
CD
FM/AM/XM
AUX
T
E
S
T
S
T
E
R
E
O
S
U
R
R
O
U
N
D
S
E
A
R
C
H
M
O
D
E
S
T
E
R
E
O
DISPLAY
SEL SEL
SETUP
TONE
SOUND
PARAMETER
REMOTE CONTROL RC-110
ENTER
VIDEO 1TAPE VIDEO 2VIDEO 3
EXT.IN
CD
FM/AM/XM
AUX
T
E
S
T
S
T
E
R
E
O
S
U
R
R
O
U
N
D
S
E
A
R
C
H
M
O
D
E
S
U
R
R
O
U
N
D
DISPLAY
SEL SEL
SETUP
TONE
SOUND
PARAMETER
REMOTE CONTROL RC-110
ENTER
VIDEO 1TAPE VIDEO 2 VIDEO 3
EXT.IN
CD
FM/AM/XM
AUX
T
E
S
T
S
T
E
R
E
O
S
U
R
R
O
U
N
D
S
E
A
R
C
H
M
O
D
E
SOUND
PARAMETER
Continued
• While playing digital signals from Dolby Digital or DTS program source or listening in a surround mode such as Dolby Pro
Logic II / Dolby Pro Logic IIx Music, Dolby Headphone, Dolby Virtual Speaker mode, you can adjust their parameters for
optimum surround effect.
When adjusting the sound parameters
1. Press the SOUND PARAMETER button.
ENGLISH