Filter
Top Products
E-11
To scan the preset stations
The stations saved in the memory can be scanned automatically. (Preset
memory scan)
Press the PRESET 1 (
or
) button for more than 0.5 seconds. The
preset number will fl ash and the programed stations will be tuned in
sequentially, for 5 seconds each.
Press the PRESET
2 (
or
) button again when the desired station
is located.
To erase entire preset memory
Press the ON/STAND-BY button to enter the stand-by mode.1
While pressing down the 2 button, press the ON/STAND-BY button
until “Tuner Clear” appears.
FUNCTION ON/ST AND-BY
Setting the clock (Remote control only)
In this example, the clock is set for the 12-hour (AM 12:00) display.
Press the ON/STAND-BY button to turn the power on.
1
Press the CLOCK/TIMER button.2
Within 10 seconds, press the ENTER button. To adjust the day, press the 3
or button and then press the ENTER button.
Press the
4 or button to select 24-hour or 12-hour display and then
press the ENTER button.
To recall a memorized station
Press the PRESET 1 (
or
) button for less than 0.5 seconds to select
the desired station.
Within 30 seconds, press the MEMORY button to store that station in
4
memory. If the “MEMORY” and preset number indicators disappear
before the station is memorized, repeat the operation from step 2.
Repeat steps 1 - 4 to set other stations, or to change a preset station.
5
When a new station is stored in the memory, the station previously
memorized for that preset channel number will be erased.
Note:
The backup function protects the memorized stations for a few hours should
there be a power failure or the AC power cord become disconnected.
Listening to the radio
Tuning
Press the ON/STAND-BY button to turn the power on.1
Press the TUNER button repeatedly to select the desired 2 frequency 2
band (FM or AM).
Press the TUNING
3 (
or
) button on the remote control to tune in to
the desired station.
Manual tuning:
Press the TUNING (
or
) button repeatedly to tune in to the
desired station.
Auto tuning:
When the TUNING (
or
) button is pressed for more than 0.5
seconds, scanning will start automatically and the tuner will stop at
the fi rst receivable broadcast station.
Notes:
When radio interference occurs, auto scan tuning may stop automatically
at that point.
Auto scan tuning will skip weak signal stations.
To stop the auto tuning, press the TUNING
(
or
) button again.
To receive an FM stereo transmission:
Press the TUNER button to select stereo mode and “ST” indicator will be
displayed. “ ” and “ ” will appear when an FM broadcast is in stereo.
If the FM reception is weak, press the TUNER button to extinguish
the “ST” indicator. The reception changes to monaural, and the sound
becomes clearer.
Memorising a station
You can store 40 AM and FM stations in memory and recall them at the push
of a button. (Preset tuning)
Perform steps 1 - 3 in “Tuning”.
1
Press the MEMORY button.2
Within 30 seconds, press the PRESET 3 (
or
) button to select the
preset channel number. Store the stations in memory, in order, starting
with preset channel 1.
The 12-hour display will appear.
(AM 0:00 - PM 23:59)
The 24-hour display will appear.
(0:00 - 23:59)
The 12-hour display will appear.
(AM 12:00 - PM 11:59)
XL-HF201P_HF301P_US.indd 11XL-HF201P_HF301P_US.indd 11 3/7/2012 10:35:26 AM3/7/2012 10:35:26 AM