Filter
Top Products
E-10
EN
■ Repeat play
Repeat play can play one track, all tracks or a programmed se-
quence continuously.
T
o repeat one track:
Select desired track using the
or
button.
Press the PLAY MODE button repeatedly until “Repeat One” ap-
pears. Press the
/ (CD / ) button.
To repeat all tracks:
Press the PLAY MODE button repeatedly until “Repeat All” ap
-
pears. Press the
/ (CD / ) button.
To repeat desired tracks:
Perform steps 1 - 5 in “Programmed play” section on this page
and then press the PLAY MODE button repeatedly until “Repeat
All” appears.
To repeat one folder:
While in Folder mode on (MP3/WMA), press PLAY MODE button
repeatedly until “Repeat Folder” appears. Press the
/ (CD / )
button.
To cancel repeat play:
Press the PLAY MODE button repeatedly until “Normal” appears
and “
” disappears.
Caution:
After performing repeat play, be sure to press the
button.
Otherwise, the disc will play continuously.
■ Programmed play (CD)
1 While in the stop mode, press the MEMORY button on the
remote control to enter the programming save mode.
2 Press the or button to select the desired track.
Selected track number
3 Press the MEMORY button to save the track number.
4 Repeat steps 2 - 3 for other tracks. Up to 32 tracks can be
programmed. If you want to check the programmed tracks,
during stop mode, press the MEMORY button repeatedly.
To clear the programmed tracks, press the CLEAR but-
ton.
5 Press the / (CD / ) button to start playback.
■ Programmed play (MP3/WMA)
1
While in the stop mode, press the MEMORY button to
enter the programming save mode.
2 Press the PRESET ( or ) button on the remote con-
trol to select the desired folder.
Then press the or button (remote control) to se-
lect the desired tracks.
3 Press the MEMORY button to save the folder and track
number.
4 Repeat steps 2 – 3 for other folder/tracks. Up to 32
tracks can be programmed.
5 Press the / (CD / ) button to start playback.
To cancel the programmed play mode:
During programmed stop mode, press the
button. The
display will show “Memory Clear” and all the programmed
contents will be cleared.
Adding tracks to the program:
If a program has been previously stored, the “MEM” in-
dicator will be displayed. During stop mode, press the
MEMORY button once. Within 10 seconds, press and hold
the MEMORY button again. Then follow steps 2 - 3 to add
tracks.
Notes:
● When the disc compartment is opened, the program is
automatically cancelled.
● If you press the ON/STANDBY button to enter the
standby mode or change the function from CD to an-
other, the programmed selections will be cleared.
■ Procedure to playback MP3/WMA disc
with folder mode on
To play back CD-R/RW.
1 In CD function, load an MP3/WMA disc. Press the
FOLDER button and disc info will be displayed.
MP3 indicator
Total number of les
TOTAL indicatorWMA indicator
Total number of folder
2 Press the PRESET ( or ) button to select desired
playback folder. (Folder mode on)
FOLDER
indicator
FOLDER number First track number in
the folder
3 Select desired le to be played back by pressing the
or button.
4 Press the / (CD / ) button. Playback will start and
le name will be displayed.
● Title, Artist and Album name are displayed if they
are recorded on the disc.
● In case of playback with the folder mode on, press
the PRESET (
or ) button, and the folder can
be selected even though it is in playback/pause
mode. It will continue playback/pause mode in the
1st track of the selected folder.
● Display content can be changed by pressing the
DISPLAY button.
Title displayCounter display
Album display
Folder displayFile name display
Artist display
Note:
If “Not Support” is displayed, it means “Copyright protected
WMA le” or “Not supported playback le” is selected.
Listening to a CD or MP3/WMA disc (continued)