Filter
Top Products
Other connections
08
54
En
1 Connect the front, surround, center and subwoofer
outputs on your DVD player to the corresponding
MULTI CH
input jack on this receiver.
• Use standard RCA/phono jack cables for the
connections.
2 If your DVD player also has outputs for surround
back channels, connect these to the corresponding
MULTI CH
input jacks on this receiver.
• Use standard RCA/phono jack cables for the
connections.
• If there is a single surround back output, connect it to
the
SURROUND BACK L (Single)
jack on this
receiver.
Selecting the multichannel analog inputs
If you have connected a decoder or a DVD player as
above, you must select the analog multichannel inputs
for surround sound playback.
1
1 Make sure you have set the playback source to the
proper output setting.
For example, you might need to set your DVD player to
output multichannel analog audio.
2 Use the
INPUT SELECT
button to select
MULTI CH
IN
.
You can also use the
INPUT SELECTOR
dial on the front
panel.
• Depending on the DVD player you’re using, the
analog output level of the subwoofer channel may be
too low. In this case, the output level of the subwoofer
can be increased by 10 dB in the Multi Ch In Setup in
Other Setup. For details, see
Multi Channel Input
Setup
on page 66.
Speaker B setup
Caution
•
Before making or changing the connections
, switch off
the power and disconnect the power cord from the
power outlet. Plugging in components should be the
last connection you make with your system.
• Be careful not to allow any contact between speaker
wires from different terminals.
• You can use speakers with a nominal impedance
between 6
Ω
to 16
Ω
(please see
Switching the
speaker impedance
on page 71 if you plan to use
speakers with an impedance of less than 8
Ω
).
After selecting
Speaker B
in
Surround back speaker
setting
on page 40, you can use the speakers connected
to the (surround back) B speaker terminals on the rear
panel to listen to stereo playback in another room. See
Switching the speaker system
below for the listening
options with this setup.
1 Connect a pair of speakers to the surround back
speaker terminals on the rear panel.
Connect them the same way you connected your
speakers in
Installing your speaker system
on page 19.
Make sure to review
Placing the speakers
on page 20
when placing the speakers in another room.
2 Select ‘
Speaker B
’ from the ‘Surr Back System’
menu.
See
Surround back speaker setting
on page 40 to do this.
Switching the speaker system
If you selected
Speaker B
in
Surround back speaker
setting
on page 40, three speaker system settings are
possible using the
SPEAKERS
button. If you selected
Normal (default)
or
Front Bi-Amp
, the button will
simply switch your main speaker system on or off. The
options below are for the
Speaker B
setting only.
2
• Use the SPEAKERS button on the front panel to
select a speaker system setting.
As mentioned above, if you have selected
Normal
(default)
, the button will simply switch your main
speaker system (A) on or off.
Note
1• When playback from the multichannel inputs is selected, you can’t use Midnight/Loudness, Dialog Enhancement or the
SIGNAL SELECT
and
ANALOG ATT
buttons, as well as any of the listening modes (including
STEREO
and the surround back channel processing).
• When playback from the multichannel inputs is selected, only the volume and channel levels can be set.
• You can’t listen to your speaker B (Second Zone) system during playback from the multichannel inputs.
RECEIVER SOURCE
SYSTEM OFF
INPUT
SELECT
DVD TV
BD TV CTRL
CD
HOME MEDIA
CD-R
HDMI
2• The subwoofer output depends on the settings you made in
Manual speaker setup
on page 48. However, if
SP
B
is selected above, no sound is heard
from the subwoofer (the LFE channel is not downmixed).
• Depending on the settings in
Surround back speaker setting
on page 40 output from the surround back pre-out terminals may change.
• All speaker systems (except
Speaker B
connections) are switched off when headphones are connected.
VSX_LX60LX70.book 54 ページ ２００７年７月１８日 水曜日 午前１０時１９分