Pioneer VSX-D409 Speaker User Manual


 
35
Operation
Displays & Controls
ATT
Use to attenunate (lower) the level of an analog
input signal and prevent distortion (refer to p.31
=). To use first press the RECEIVER button then
operate this button.
CHANNEL LEVEL +/– (see page 22-note)
Use to set up the levels of the surround sound of
the receiver. To use first press the RECEIVER
button then operate this button.
SIGNAL SELECT (see page 37)
Use to select the proper signal (analog, digital) for
the source your are inputting. To use first press
the RECEIVER button then operate this button.
4 THE FOLLOWING FOUR SETS OF
BUTTONS ARE DEDICATED TV
CONTROL. THEY ARE ONLY USED
FOR CONTROLLING YOUR TV.
FUNC button
Use select the TV function.
TV POWER button
Use to turn on the power of the TV.
TV CHANNEL +/– buttons
Use to change channels on your TV.
TV VOLUME +/– buttons
Use to adjust the volume on your TV.
5 MENU button
Use to access different menus associated with
your DVD player.
6 SOURCE button
Use to turn on/off other components connected
to the receiver.
7 THE FOLLOWING BUTTONS ARE
BOTH CONTROLS FOR OTHER
COMPONENTS (LIKE A DVD PLAYER)
AND DEDICATED TUNER CONTROLS.
THE TUNER CONTROLS ARE
EXPLAINED HERE. YOU CAN USE
THEM AFTER YOU HAVE PUSHED THE
TUNER MULTI CONTROL BUTTON.
CLASS button (see pages 43, 44)
Use to switch between the three banks (classes)
of station memories.
MPX MODE button (see page 42)
Use to switch between auto stereo and mono
reception of FM broadcasts. If the signal is weak
then switching to MONO will improve the sound
quality. Also, this is the pause button for CDs,
tapes, DVDs, etc.
BAND button (see pages 42, 43)
Use to switch between the AM and FM band
when in TUNER mode.
D. ACCESS button (see page 43)
Use to directly access a radio station by pressing
the number of the station you want.
8 LOUDNESS button
Use to switch on the loudness. This feature is
useful for getting good bass and treble sounds
listening at low volumes.
9 FUNCTION button
Use select the playback or recording source. This
button lets you cycle through the different
functions of the receiver in the following order:
CD, tuner, AUX, CDR/TAPE, VCDR/DVR, DVD/
LD, DVD 5.1 CH., and TV/SAT.
0 RECEIVER (POWER) button
This switches between STANDBY mode and
power ON for this receiver.
- FL DIMMER button
Use this button to make the fluorescent display
(FL) dimmer or brighter. There are three
brightness settings as well as an off setting.
= LED DISPLAY (see pages 24-25)
This display flashes when a command is sent
from the remote control to the receiver. It also
flashes at other times, for example when
teaching the receiver preset codes, with specific
meanings.
~ EFFECT +/– buttons (see page 41-note)
Use to add or subtract the amount of effect in
different DSP sound modes or advanced
listening modes.
! 2 3 5∞ ( FQ +/–) & ENTER buttons
(see pages 16-21, 42)
Use these arrow buttons when setting up your
surround sound system (see pages 14-15).
These buttons are also used to control DVD
menus/options and for deck 1 of a double
cassette deck player. The FQ +/– buttons can be
used to find radio frequencies.
@ TOP MENU button
In DVD mode this button brings you to the top or
most fundamental menu.
# CHANNEL +/– buttons
Use to select the stations of memorized radio
frequencies. Also use to skip tracks backward or
forward on CDs, DVDs, etc.
$ MUTING button
Use to mute the sound or restore the sound if it
has been muted.
% MASTER VOLUME +/– buttons
Use to set the overall listening volume.
^ REMOTE SETUP button (see page 24)
Use this button when setting up the remote
control to control other components.