Filter
Top Products
ENGLISH
RQTV0156
16
Before playback
AUTO
SPEAKER SETUP
ADVANCED
DUAL AMP
BI-AMP
SPEAKERS
A B
AUTO DETECTOR
SURROUND
AUX SETUP MIC
MENU
SETUP
RETURN
INPUT SELECTOR
ENTER
VOLUME
HDMI
TUNE
S VIDEO IN
VIDEO IN
L
A
U
DIO
IN
R
[ ]
SPEAKERS
A B
AUTO DETECTOR
AUTO
SPEAKER SETUP
O
N
E
T
O
U
C
H
P
L
A
Y
D
I
R
E
C
T
N
A
V
I
G
A
T
O
R
T
O
P
M
E
N
U
F
U
N
C
T
I
O
N
S
0
RECEIVER
AV
SYSTEM
TV
RECORDER
DVD
DV
D
PLAYER
ANALOG 6CH
VCRCD
TUNER
BAND
CH
VOLUME
DIRECT TUNING
SKIP
SLOW/SEARCH
STOP
PAUSE
PLAY
DRIVE SELECT
DVD RECORDER
MANUAL SKIP
ENTER
SUB MENU RETURN
OFF
SUBWOOFER
TEST
TV
LEVEL
EFFECT
VOL
NEO
:
6
SFC
MUSIC MOVIE
DIMMER
MUTING
TV/AV
DISC
-
/
--
AUTO
Before playback
Message Solutions Pages
“INSERT MIC” Calibration microphone is not detected. Insert the microphone correctly.• 14
“NO SIGNAL” Check that the calibration microphone is connected correctly.• 14
“DISTANCE ERROR” Bring the speakers nearer to the calibration microphone.• -
“NOISY” Setup in a quiet environment or do auto speaker setup at a quieter time of day.
Turn off equipment that may produce noise, such as air conditioners.
•
•
-
-
“MEASURING ERROR” Change the positions of the speakers and perform the setup again.• -
“CHECK CONNECTION
TO SBL SPEAKER”
Left surround back speaker not detected. If you have decided to use only one
surround back speaker, connect it to the SURROUND BACK (L) terminal.
Check connection to left surround back speaker.
•
•
13
13
“NEED TO CONNECT
LS/RS SPEAKERS”
Surround speakers not detected. You must have surround speakers connected
before you can connect and use surround back speakers effectively.
• 13
“CHECK
CONNECTIONS TO
LS/RS SPEAKERS”
One or both surround speakers not detected. Check the connections.• 13
“CHECK
CONNECTIONS TO L/R
SPEAKERS”
Check the front (L) and (R) connections.• 13
“LOW SIGNAL” Change the position (height and direction) of the microphone.
Make sure there is nothing around the microphone that could interfere with the test
tones.
Make sure the volume of the subwoofer is set to the level you would normally use.
•
•
•
-
-
17
Troubleshooting for auto speaker setup
While performing auto speaker setup, errors may occur and the messages will blink or scroll on the display, depending on the
conditions. Press any button on the main unit or remote control to stop the setup.
After troubleshooting, press and hold for 2 seconds to start the setup process again.
TEST
AUTO
Auto speaker setup
Auto speaker setup may produce an unsatisfactory result with some speaker setups and configurations.
You can perform auto speaker setup even if SPEAKERS A are off.
For subwoofer, only level is adjusted in auto speaker setup.
All settings in auto speaker setup return to the factory setting if you do automatic speaker detection (➡ page 17) separately, or,
change the speaker size (except for front speakers) from “NO” or “NONE” to other size settings (“Speaker and size settings”,
➡ page 27).
Auto speaker setup will not start if you have muted the speakers. Turn the muting off (➡ page 31).
HDAVI Control
TM
(➡ page 21) is disabled during auto speaker setup.
•
•
•
•
•
•
Note
SA-XR58.indb 16 6/27/2006 6:55:01 PM