Filter
Top Products
ENGLISH
RQTV0156
15
Before playback
Auto speaker setup
3
Start performing auto speaker setup.
4
Auto speaker setup finishes.
Loud test tones are output from each speaker during the
configuration.
The checked settings display for a minimum of 3 seconds
each.
•
•
To cancel during setup
Press any button on the main unit or remote control. “CANCELED” appears on the display.
a) Press and hold for about 2 seconds.
TEST
AUTO
[AUTO SPEAKER SETUP] indicator starts flashing.
“AUTO SETUP” appears on the display.
•
•
AUTO
SPEAKER SETUP
AUTO
SPEAKER SETUP
b) The unit checks that you have correctly connected the
calibration microphone.
c) The automatic setup starts the automatic speaker detection,
STEP 1, STEP 2, and STEP 3 calibration as follows.
“COMPLETE” appears on the display and all calibrations are saved.
[AUTO SPEAKER SETUP] indicator lights.
To exit, press .
Disconnect the calibration microphone.
•
•
•
•
During setup, operations may stop when there is an error message on the display. Refer to page 16 for
troubleshooting.
Turn on the unit.
Press
The standby indicator goes off when you turn on the unit.•
O
N
E
T
O
U
C
H
P
L
A
Y
D
I
R
E
C
T
N
A
V
I
G
A
T
O
R
T
O
P
M
E
N
U
F
U
N
C
T
I
O
N
S
0
RECEIVER
AV
SYSTEM
TV
RECORDER
DVD
DV
D
PLAYER
ANALOG 6CH
VCRCD
TUNER
BAND
CH
VOLUME
DIRECT TUNING
SKIP
SLOW/SEARCH
STOP
PAUSE
PLAY
DRIVE SELECT
DVD RECORDER
MANUAL SKIP
ENTER
SUB MENU RETURN
OFF
SUBWOOFER
TEST
TV
LEVEL
EFFECT
VOL
NEO
:
6
SFC
MUSIC MOVIE
DIMMER
MUTING
TV/AV
DISC
-
/
--
AUTO
AUTO
SPEAKER SETUP
ADVANCED
DUAL AM
P
BI-AMP
SPEAKERS
A B
AUTO DETECTOR
SURROUND
AUX SETUP MIC
TUNE
S VIDEO IN
VIDEO IN
L
AU
DIO IN
R
AUTO
SPEAKER SETUP
↓
Speaker abbreviations
L: Front left C: Center R: Front right
S: Surround RS: Surround right LS: Surround left
SB: Surround
back
SBR: Surround back
right
SBL: Surround back
left
W/SUBW: Subwoofer
↓
↓
STEP1 L→STEP1 C→STEP1 R→STEP1 RS→STEP1 SBR
→STEP1 SBL→STEP1 LS→STEP1 SUBW→PROCESSING
STEP2 L→STEP2 C→STEP2 R→STEP2 RS→STEP2 SBR
→STEP2 SBL→STEP2 LS→STEP2 SUBW→PROCESSING
STEP3 L→STEP3 C→STEP3 R→STEP3 RS→STEP3 SBR
→STEP3 SBL→STEP3 LS→STEP3 SUBW→PROCESSING
TEST
AUTO
For your reference
Turn off all components before making any connections.
Peripheral equipment and cables sold separately unless
otherwise indicated.
To connect equipment, refer to the appropriate operating
instructions.
•
•
•
(Automatic speaker
detection)
Note
Perform auto speaker setup again if you have changed the speakers, speaker positions, or the layout of your listening environment.
SA-XR58.indb 15 6/27/2006 6:55:00 PM