Filter
Top Products
RQT7114
23
Other functions
Using with other equipment
Before use
•Switch [PLAY SELECT] to select the media to be used
•Turn [MODE] on the rear panel to TURNTABLE
•Insert the SD Memory Card or CD to be used
Start play using the mixer’s fader
You can instantly start play from the auto cue point or cue point on this
unit using the mixer’s fader by connecting this unit to the control ter-
minal of a DJ mixer using a control cable connection. ( page 8)
Before use :
•Adjust buttons and control knobs of CH1 and CH4 on the DJ mixer
so mixed sound is output from the master output.
•Turn the DJ mixer’s FADER START CH1 and CH4 to on.
•On unit 1 or 2, set the auto cue point or set the cue point and select
the cue bank.
Starting with the channel fader
(e.g.)
When the fader operation switch on the DJ mixer is set to NORMAL
1. On the DJ Mixer, change the C.FADER ASSIGN A
switch to other than 1 and change the C.FADER AS-
SIGN B switch to other than 4
2.
Push the CH1, CH4 channel fader all the way to the bottom
3. During play or while paused on unit 1 or 2, press
[CUE STOP] (Back cue)
•Returns to the set point and pauses.
4. When you want to start play, push the CH1 or CH4
channel fader up
•At the same time, play begins from the set point on unit 1 or 2.
•
After you return the channel fader to its original position, unit back cues,
and pauses after returning to the set point.
Starting with the cross fader
(e.g.) When the cross fader operation switch on the DJ mixer is set to
NORMAL and to start play on CH1
1. On the DJ Mixer, change the C.FADER ASSIGN A
switch to 1 and change the C.FADER ASSIGN B
switch to 4
2. Push the cross fader all the way toward CH4 (
)
3. During play or while paused on unit 1, press [CUE
STOP] (Back cue)
4. When you want to start play, push the cross fader in
the opposite direction indicated in step 2, towards
CH1 ( )
•At the same time, play begins from the set point on unit 1.
You can relay play by connecting the control terminals of the two units.
( page 9)
Before use:
•Turn Auto Cue on for both units, set the auto cue point for the track
to be played and back cue.
Using two units for relay play
Press [PLAY/PAUSE] on the unit to be
played first
•Once track play finishes on the unit being played, play auto-
matically begins from the unit on standby.
•The unit that was played first pauses and cues at the next track’s
auto cue point.
•You can automatically alternate play between both units by repeat-
ing this method.
•You can listen to many different tracks by changing the media and
selecting the track of the unit in the standby position.
•Set the cue point, select the cue bank and back cue on the standby
unit to begin relay play from the desired point of the desired track.
Note
•During play, if power on one of the units is cut or turned off, play
may begin on the other standby unit.
•You cannot use fader start and relay play at the same time.
Using the amplifier and other equipment
Connect with the matching input terminals on the equipment (not in-
cluded). ( page 9)
•When using this unit’s DIGITAL OUT terminal, SD Audio is not out-
put.
1 Put the equipment on standby
2 Press [PLAY/PAUSE] to play
•Audio played from the connected equipment is output.
•You can alternate play by back cueing unit 2 connected to
CH4.
Push the cross fader all the way toward CH4 Play CH4
CH1 Back cue
Push the cross fader all the way toward CH1 Play CH1
CH4 Back cue