Filter
Top Products
27
En
Note
*1
If Direct listening mode is selected, “Dynamic EQ” and
“Dynamic Volume” cannot be selected.
*2
Only when you have selected “Custom” in the “Picture
Mode” (➔ 46), pressing ENTER allows you to adjust the fol-
lowing items; “Brightness”, “Contrast”, “Hue”, and “Satu-
ration”. Press RETURN to return to the original Video menu.
*3
Depending on the input source and listening mode, not all
channels shown here output the sound.
*4
When you have entered a custom name in “Name Edit”
(➔ 45), the input source is displayed with that name. But
even if not, the component name may be displayed if the AV
receiver receives it via HDMI connection (➔ 19).
*5
For the PORT input selector, the name of Universal Port
Option Dock will be displayed.
When you connect an -capable Onkyo component, you
must configure the input display so that can work
properly.
This setting can be done only from the front panel.
Note
• DOCK can be selected for the TV/CD, GAME or VCR/DVR
input selector, but not at the same time.
• Enter the appropriate remote control code before using the
remote controller for the first time (➔ 60).
Note
• Always turn down the volume before connecting your head-
phones.
• While the headphones plug is inserted in the PHONES jack, the
speakers are turned off. (The Powered Zone 2 speakers are not
turned off.)
• When you connect a pair of headphones, the listening mode is
set to Stereo, unless it’s already set to Stereo, Mono or Direct.
• Only the Stereo, Direct and Mono listening modes can be used
with headphones.
2
Use / / / to make the desired selection.
■Audio
*1
`You can change the following settings: “Bass”,
“Treble”, “Subwoofer Level”, “Center Level”,
“Dynamic EQ”, “Dynamic Volume”, “Late
Night”, “Music Optimizer”, “Cinema filter”
and “Audio Selector”.
See also:
• “Audyssey” (➔ 44)
• “Using the Audio Settings” (➔ 50)
■Video
*2
`You can change the following settings: “Wide
Mode” and “Picture Mode”.
See also:
• “Picture Adjust” (➔ 46)
■Info
*3*4
`You can view the information of the following
items: “Audio”, “Video” and “Tuner”.
■Input Sel
*4*5
`You can select the input source while viewing
the information as follows: the name of input
selectors, input assignments, and radio informa-
tion, and ARC function setting.
Press ENTER to display the current input
source, followed by / to select the desired
input source. Pressing ENTER again switches to
the selected input source.
■Listening Mode
`You can select the listening modes that are
grouped in the following categories: “MOVIE/
TV”, “MUSIC” and “GAME”.
Use / to select the category and / to
select the listening mode. Press ENTER to
switch to the selected listening mode.
Changing the Input Display
1
Press TV/CD, GAME or VCR/DVR so that “TV/
CD”, “GAME” or “VCR/DVR” appears on the
display.
2
Press and hold down TV/CD, GAME or VCR/DVR
(about 3 seconds) to change the input display.
Repeat this step to select “MD”, “CDR”, “DOCK”
or “TAPE”.
For the TV/CD input selector, the input display
changes in this order:
For the GAME input selector, the setting changes in
this order:
For the VCR/DVR input selector, the setting
changes in this order:
Using Headphones
Connect a pair of stereo headphones with a stan-
dard plug (1/4 inch or 6.3 mm) to the PHONES
jack.
TV/CD → MD → CDR
DOCK
→
→
TAPE
→
GAME ↔ DOCK
VCR/DVR ↔ DOCK