Filter
Top Products
47
En
Note
*1
“Full Band” can be selected only when “Full Band” is
selected in the “Front” setting.
*2
If the “Surround” setting is set to “None”, this setting cannot
be selected.
*3
If the “Surround” setting is set to anything other than “Full
Band”, “Full Band” cannot be selected here.
*4
If the “Speakers Type(Front)” setting is set to “Bi-Amp”, or
the “Powered Zone 2” setting is set to “Yes”, this setting
cannot be selected.
■ Surround Back Ch
`1ch:
Select if only one surround back speaker L is
connected.
`2ch
:
Select if two (left and right) surround back speakers
are connected.
Note
•If the “Surround Back” Setting is set to “None”, this setting
cannot be selected.
■ LPF of LFE
(Low-Pass Filter for the LFE Channel)
`80Hz, 90Hz, 100Hz, 120Hz
`Bypass:
Low-Pass Filter is not applied.
With this setting, you can specify the cutoff frequency
of the LFE channel’s low-pass filter (LPF), which can
be used to filter out unwanted hum. The LPF only
applies to sources that use the LFE channel.
Note
• If you’re using THX-certified speakers, select “80Hz”.
■ Double Bass
`On
`Off(THX)
Turn this setting on to boost bass output by feeding bass
sounds from the front left, right, and center channels to the
subwoofer.
Note
• This function can be set only if the “Subwoofer” setting is set to
“Yes”, and the “Front” setting is set to “Full Band”.
• If you’re using THX-certified speakers, select “Off(THX)”.
■ Subwoofer Phase
`0
º
`180º:
Moves the subwoofer phase.
Note
•If the “Subwoofer” setting is set to “No”, this setting cannot be
selected (➔ page 46).
■ Wireless Subwoofer
`Yes:
The audio is output from the speakers connected to
the wireless unit.
`No
:
The audio is not output from the speakers connected
to the wireless unit.
When the wireless unit is connected to the UNIVERSAL
PORT jack on the AV receiver, you can select if you wish
to output the audio from the speakers connected to the
wireless unit.
Note
• If the “Subwoofer” setting is set to “No”, this setting cannot be
selected (➔ page 46).
Speaker Distance
Here you can specify the distance from each speaker to the
listening position so that the sound from each speaker
arrives at the listener’s ears as the sound designer
intended.
■ Unit
`feet:
Distances can be set in feet. Range: 0.5ft to 30.0ft in
0.5 foot steps.
`meters:
Distances can be set in meters. Range: 0.15m to
9.00m in 0.15 meter steps.
(The default setting varies from country to country.)
■ Left, Front Wide Left, Front High Left, Center,
Front High Right, Front Wide Right, Right,
Surround Right, Surround Back Right,
Surround Back Left, Surround Left, Subwoofer
`Specify the distance from each speaker to your
listening position.
Note
• These settings are not available in either of the following cases:
– a pair of headphones is connected.
–the “Audio TV Out” setting is set to “On” (➔ page 58).
–“HDMI Control(RIHD)” is set to “On” (➔ page 57) and
you’re listening through your TV speakers.
• Speakers that you set to “No” or “None” in the
“Speaker Configuration” cannot be selected (➔ page 46).
This setting is NOT set automatically by
Audyssey MultEQ
®
XT Room Correction and Speaker
Setup function (➔ page 31).
When an optional unit is connected to the
UNIVERSAL PORT jack on the AV receiver, the
speaker setting menu may appear on screen.
This setting is set automatically by
Audyssey MultEQ XT Room Correction and Speaker
Setup function (➔ page 31).