Filter
Top Products
42
ENGLISH
BASIC OPERATION (TUNER)
LISTENING TO THE TUNER
Frequency scan step for AM is selectable.
Default setup is 10 kHz step, if your country’s standard is 9 kHz step,
touch “AM” button on the remote more than 6 seconds. Scan step will
change.
Note:
• Preset memory for the tuner will clear by changing this setup.
AUTO TUNING
(USING THE SR9200)
1.
To select tuner and desired band (FM or AM), press the TUNER
button on the front panel.
2.
Press the AUTO-TUNE button on front panel, “AUTO TUNING”
appears on the display.
3.
Rotate the GYRO TUNING dial.
4.
Automatic searching begins then stops when a station is tuned in.
(Using the remote control unit)
1.
To select tuner and desired band (FM or AM), tap desired band
FM or AM on the remote.
2.
Touch Tuning^ or Tuning
v
more than 1 second on the remote.
3.
Automatic searching begins then stops when a station is tuned in.
If tuning does not stop at the desired station, use to the “Manual
tuning” operation.
MANUAL TUNING
(USING THE SR9200)
1.
To select tuner and desired band(FM or AM), press the TUNER
button on the front panel
2.
Press the F/P(Frequency/Preset) button on front panel , to
appears frequency on the display.
3.
Rotate the GYRO TUNING dial to tune in the desired station.
(Using the remote control unit)
1.
To select tuner and desired band(FM or AM), tap desired band
FM,or AM on the remote.
2.
Tap Tuning^ or Tuning
v
on the remote to tune in the desired
station.
DIRECT FREQUENCY CALL
1.
To select tuner and desired band(FM or AM), tap desired band
FM, or AM on the remote.
2.
Tap the Freq. Direct on the remote, display will show “FREQ -- --”.
3.
Input your desired station’s frequency with ten keypad on the
remote.
4.
The desired station will automatically be tuned.
(FM) TUNING MODE (AUTO STEREO OR MONO)
When in the auto stereo mode, AUTO indicator keeps to light on the
display.
The “ST” indicator lights on when a stereo broadcast is tuned in.
At open frequencies, the noise is muted and the “TUNED” and “ST”
indicators turn off.
If the signal is weak, it may be difficult to tune into the station in stereo.
In such a case, press the T-MODE button n the front panel or tap
Streo/Mono on the remote control unit.
“AUTO” indicators turn off ,FM stereo broadcasts are received in
monaural and the “ST” indicator turns off.
To return to auto stereo mode, press the T-MODE button or tap Streo/
Mono on the remote control unit again. AUTO indicator lights on the
display.
PRESET MEMORY
With this unit you can preset up to 50 FM/AM stations in any order.
For each station, you can memorize the frequency and reception
mode if desired.
AUTO PRESET MEMORY
This function automatically scans the FM and AM band and enters all
stations with proper signal strength into the memory.
1.
To select FM , press the TUNER button on the front panel.
2.
While pressing the MEMO button , rotate the GYRO TUNING dial
to up.
“AUTO PRESET” will appear on the display, and scanning starts
from lowest frequency.
VOLUME
UPDOWN
MUTE ATT
7.1CH-IN
LD DSS TAPE CD-RCDTV VCR 1 VCR2/DVD-R
MULTI-SPK
MULTI ROOM
AUX1S-DIRECT
AUX2A/D
SLEEP
AUTO-TUNE
GYRO TUNINGDOWN UP
T-MODEF/P
AUX1 INPUT
R
AUDIO
L
VIDEO
S-VIDEO
DIGITAL
MEMO
CLEARDISPLAY
DVD TUNER
3. 2. 1.
1.
2.
VOLUME
UPDOWN
MUTE ATT
7.1CH-IN
LD DSS TAPE CD-RCDTV VCR 1 VCR2/DVD-R
MULTI-SPK
MULTI ROOM
AUX1S-DIRECT
AUX2A/D
SLEEP
AUTO-TUNE
GYRO TUNINGDOWN UP
T-MODEF/P
AUX1 INPUT
R
AUDIO
L
VIDEO
S-VIDEO
DIGITAL
MEMO
CLEARDISPLAY
DVD TUNER
3. 2. 1.
1.
2.
2.
1.
3.
VOLUME
UPDOWN
PHONES
MUTE ATTENTER
7.1CH-IN
LD DSS TAPE CD-R TUNERCDTV VCR 1 VCR2/DVD-R
MULTI-SPK
MULTI ROOM
AUX1S-DIRECT
AUX2A/D
SLEEP
AUTO-TUNE
GYRO TUNINGDOWN UP
T-MODEF/P
AUX1 INPUT
R
AUDIO
L
VIDEO
S-VIDEO
DIGITAL
MEMO
CLEARDISPLAY
DVD
POWER ON/STANDBY
STANDBY
VOLUME
UPDOWN
PHONES
SELECT MUTE ATTENTER
SELECTOR
7.1CH-IN
LD DSS TAPE CD-RCDTV VCR 1 VCR2/DVD-R
MULTI-SPK
MULTI ROOM
AUX1S-DIRECT
AUX2A/D
SLEEP
AUTO-TUNE
GYRO TUNINGDOWN UP
T-MODEF/P
AUX1 INPUT
R
AUDIO
L
VIDEO
S-VIDEO
DIGITAL
MEMO
CLEARDISPLAY
DVD TUNER
2.4. 3.
-2)
2.5. 1. 3.
-1)