Filter
Top Products
33
ENGLISH
BASIC OPERATION (PLAY BACK)
SELECTING AN INPUT SOURCE.
Before you can listen to any input media, you must first select the input
source at the SR9200.
E.G. : DVD
To select DVD, simply press the DVD button on the front panel or tap
DVD on the remote.
After you have selected DVD, simply turn on the DVD player and play
the DVD.
• As the input source is changed, the new input name will appear
momentarily as an OSD information on the video display.The input
name will also appear in the display on the front-panel.
• As the input is changed, the SR9200 will automatically switch to the
digital input, surround mode, attenuation, and night mode status
that were entered during the configuration process for that source.
• When an audio source is selected, the last video input used remains
routed to the VCR1 & VCR2 Outputs and Monitor 1&2 Outputs.
This permits simultaneous viewing and listening to different
sources.
• When a Video source is selected, the video signal for that input will
be routed to the Monitor 1&2 Outputs jack and will be viewable on
a TV monitor connected to the SR9200.
If a component video input is connected to the DVD or DSS
component inputs, it will be routed to the Component Video
Output. Make certain that your TV is set to the proper input to view
the signal.
SELECTING THE SURROUND MODE
E.G. : AUTO SURROUND
To select the surround mode during playback, turn the SELECT knob
on the front panel or tap the surround mode icon on the remote .
ADJUSTING THE MAIN VOLUME
Adjust the volume to a comfortable level using the VOLUME control
knob on the front panel or VOL / buttons.
To increase the volume, turn the VOLUME knob to the right or press
VOL button on the remote, to decrease the volume, turn the it to the
left or press VOL button on the remote.
Notes:
• The volume can be adjusted within the range of – ∞ to 18 dB, in
steps of 1 dB.
• However, when the channel level is set as described on page 25,
if the volume for any channel is set at +1 dB or greater, the
volume cannot be adjusted up to 18 dB.
(In this case the maximum volume adjustment range is “18 dB -
(Maximum value of channel level)”.)
ADJUSTING THE TONE(BASS & TREBLE)
CONTROL.
During a listening session you may wish to adjust the Bass and Treble
Control to suit your listening tastes or room acoustics.
(using the SR9200)
To change the selector mode , press SELECT button, until "BASS" or
"TREBLE" is shown on front display.
Turn the SELECTOR knob to desired level of tone control.
(Using the remote control unit)
To adjust the bass effect , tap Bass+ or Bass on the remote.
To adjust the treble effect , tap Treble+ or Treble– on the remote.
Notes :
• The tone control function can work in the AUTO Surround,
Stereo, Dolby PL2, DTS, DTS-ES, and Multi Ch. Stereo mode.
• If digital input signal is PCM 96kHz, tone control is disable.
POWER ON/STANDBY
STANDBY
PHONES
SELECT ENTER
SELECTOR
7.1CH-IN
LD DSS TAPE CD-R TUNERCDTV VCR 1 VCR2/DVD-R
MULTI-SPK
MULTI ROOM
AUX1S-DIRECT
AUX2A/D
SLEEP
AUTO-TUNE
GYRO TUNINGDOWN UP
T-MODEF/P
AUX1 INPUT
R
AUDIO
L
VIDEO
S-VIDEO
DIGITAL
MEMO
CLEARDISPLAY
DVD
POWER ON/STANDBY
STANDBY
PHONES
SELECT ENTER
SELECTOR
7.1CH-IN
LD DSS TAPE CD-RCDTV VCR 1 VCR2/DVD-R
MULTI-SPK
MULTI ROOM
AUX1S-DIRECT
AUX2A/D
SLEEP
AUTO-TUNE
GYRO TUNINGDOWN UP
T-M
O
F/P
AUX1 INPUT
R
AUDIO
L
VIDEO
S-VIDEO
DIGITAL
MEMO
CLEARDISPLAY
DVD
VOLUME
UPDOWN
MUTE ATT
7.1CH-IN
DSS TAPE CD-R TUNERCDTV VCR 1 VCR2/DVD-R
MULTI-SPK
M
ULTI ROOM
AUX1S-DIRECT
AUX2A/D
SLEEP
AUTO-TUNE
GYRO TUNINGDOWN UP
T-MODEF/P
AUX1 INPUT
R
AUDIO
L
VIDEO
S-VIDEO
DIGITAL
MEMO
CLEAR
P
LAY
DVD
H
S
VOL
CH
OK
Ex
M
POWER ON/STANDBY
STANDBY
PHONES
SELECT ENTER
SELECTOR
7.1CH-IN
LD DSS TAPE CD-RCDTV VCR 1 VCR2/DVD-R
MULTI-SPK
MULTI ROOM
AUX1S-DIRECT
AUX2A/D
SLEEP
AUTO-TUNE
GYRO TUNINGDOWN UP
T-M
O
F/P
AUX1 INPUT
R
AUDIO
L
VIDEO
S-VIDEO
DIGITAL
MEMO
CLEARDISPLAY
DVD