Marantz SR8002 Stereo Receiver User Manual


  Open as PDF
of 94
 
68
ENGLISH
MANUAL PRESET MEMORY
2 31
5 64
8
0
97
MEMO
CLEAR
PREV
MUTE
MENU
EXIT
GUIDE
TEST
CH.SEL
LIP.SYNC
SURR
7.1CH
ATT
SPK-AB
DISP
OSD
THX
SLEEP
3.
2.
2 31
5 64
8
0
97
MEMO
DI
G
D
O
M-DAX
ENTER
MENU
P
URE DIRECT THX
7.1CH INPUT
MODE AUTO
MULTI
A/B
T-MODE
MEMORY CLEAR
DISPLAY
EXIT
SPEAKERS
BAND
MIC
D
IRECT
SURROUND
SPEAKER
MULTI
S
D
L
C
R
SL S SR
LFE
DIGITAL
SURROUND
V-OFFDISP MULTI AUTO TUNED STSPKR A B
NIGHT
PEAK ANALOG
DIGITAL
ATT
SLEEP
SURR DIRECT
AUTO
DISC 6.1 MTX 6.1 EQ
PCM
AAC
3.
2. 4.
(Using the unit)
1.
Tune into the radio station you desire (Refer to
the “MANUAL TUNING” or “AUTO TUNING”
section).
2.
Press the MEMORY button on the front panel.
“– –“ (preset number) starts blinking on the
display.
3.
Select the preset number by pressing the 1
or 2
cursor
buttons, while this is still blinking
(approx. 5 seconds)
4.
Press the MEMORY button again to enter. The
display stops blinking.
The station is now stored in the specifi ed preset
memory location.
(Using the remote controller)
1.
Tune into the radio station you desire (Refer to
the “MANUAL TUNING” or “AUTO TUNING”
section).
2.
Press the MEMO button on the remote
controller. “– –“ (preset number) starts blinking
on the display.
3.
Enter the desired preset number by pressing
the numeric buttons.
Note:
• When entering a single digit number (2 for example),
either input “02” or just input “2” and wait for a few
seconds.
PRESET MEMORY
With this unit you can preset up to 60 FM/AM stations
in any order.
For each station, you can memorize the frequency
and reception mode if desired.
AUTO PRESET MEMORY
This function automatically scans the FM and AM
band and enters all stations with proper signal
strength into the memory.
DIGITAL
RLVIDEO
S-VIDEO
AUX 1 INPUT
AUDIO
VOLUME
UP
DOWN
STANDBY
PHONES
INPUT SELECTOR
AV SURROUND RECEIVER SR8002
M-DAX
ENTER
MENU
PURE DIRECT THX
7.1CH INPUT
MODE AUTO
MULTI
A/B
T-MODE
MEMORY CLEAR
DISPLAY
EXIT
SPEAKERS
BAND
MIC
PURE DIRECT
SURROUND
SPEAKER
MULTI
DSD
POWER ON/OFF
L
C
R
SL S SR
LFE
DIGITAL
SURROUND
V-OFFDISP MULTI AUTO TUNED STSPKR A B
NIGHT
PEAK ANALOG
DIGITAL
ATT
SLEEP
SURR DIRECT
AUTO
DISC 6.1 MTX 6.1 EQ
PCM
AAC
2. 4.
1. 3.
5.
2.
1.
To select FM , press the BAND button on the
front panel.
2.
While pressing the MEMORY button, press the
1 cursor button.
“AUTO PRESET” will appear on the display,
and scanning starts from the lowest frequency.
3.
Each time the tuner fi nds a station, scanning
will pause and the station will be played for fi ve
seconds.
During this time, the following operations are
possible.
The band can be changed by the BAND button.
4.
If no button is pressed during this period, the
current station is memorized in location Preset
01.
If you wish to skip the current station, press the
3 cursor button during this period, this station
is skipped and auto presetting continues.
5.
Operation stops automatically when all 60
preset memory positions are fi lled or when
auto scanning attains the highest end of all
bands. If you desire to stop the auto preset
memory at anytime, press the CLEAR button.
Analog Mono Mode
T-MODE:MONO
MONO mode is selected and the AUTO indicator
disappears from the FL display. Monaural broadcasts
are received in TUNER mode.
Note:
• On the SR7002, the TUNER mode cannot be
changed when BAND is set to AM.
• The SR7002 does not display the mode on the FL
display when the TUNER MODE is switched.
The AUTO indictor appears on the FL display when
the mode is switched to Analog Auto Mode. (See
page 9)
• If the unit receives a weak signal or it is diffi cult to
receive a stereo signal, press the T-MODE button
on the remote controller or the unit to switch to
MONO mode. This reduces the amount of noise
and makes broadcasts easier to hear. The AUTO
indicator on the FL display disappears.
(FM) TUNING MODE (AUTO STEREO OR MONO)
DIGITAL
RLVIDEO
S-VIDEO
AUX 1 INPUT
AUDIO
VOLUME
UP
DOWN
M-DAX
R
A/B
T-MODE
MEMORY CLEAR
DISPLAY
EXIT
SPEAKERS
BAND
MIC
L
C
R
SL S SR
LFE
DIGITAL
SURROUND
V
-OFF
NIGHT
PEAK ANALOG
DIGITAL
ATT
6
.1 EQ
PCM
AAC
D4
D5
D2
M
D1
D3
D5
VOL
CH
USE
PAGE
2
DSS
AMP
AUX2
AUX1
TAPE
TUNER
CD
CD-R
MD
VCRDVD
TV
12
LIGHT
Learning Remote Controller
RC8001SR
TUNER
In TUNER mode, press the T-MODE button on the
remote controller to switch between AUTO STEREO
and monaural sound.
1.
Press the > button on the remote controller to
display Page 2.
2.
Each time the T-MODE (D3) button is pressed,
the TUNER mode changes and the mode is
displayed on the FL display.
Analog / Digital Auto Mode (Only on the SR8002)
T-MODE:DIG-AT
For listening to HD Radio stations.
See p.70 for more information on HD Radio
technology.
Note:
• This mode is not available on the SR7002.
Analog Auto Mode
(when receiving FM broadcasts)
T-MODE:ANA-AT
AUTO STEREO mode is selected and the AUTO
indicator is illuminated on the FL display.
When stereo broadcasts are received, the ST
indicator is illuminated on the FL display.
Note:
• This mode is not available when BAND is set to
AM.
 previous next