Filter
Top Products
ENGLISH
10
y XM terminal
See page 37 for connecting information.
u Sub Speaker outputs terminals
(MULTI SPEAKER / SPEAKER C)
Two terminals are provided for the front left, and right
speakers for multi room.
The terminals can be used to connect a third set of
speakers by setting the SPEAKER C selector switch
to ON. For connection and use, see page 38.
i Speaker outputs terminals
Nine terminals are provided for the front (A) left, front
(A) right, front (B) left, front (B) right, front center,
surround left, surround right, surround back left and
surround back right speakers.
o SPEAKER C switch
Set to ON to connect a bi-amp to this receiver or set
to OFF for normal speaker connection (surround
back and multiroom speakers). (See page 38)
!0 AC OUTLETS
Connect the AC power cables of components such as
a DVD and CD player to these outlets. SWITCHED and
UNSWITCHED outlets are provided.
The one marked SWITCHED provides power
only when the unit is turned on and is useful for
components which you use every time you play your
system.
The one marked UNSWITCHED is always live as
long as the unit is plugged into a live outlet.
A component connected here may be left on
permanently, or may be switched off with via its own
power switch.
Caution:
• In order to avoid potential turn-off thumps, anything
plugged into these outlets should be powered up
before the unit is turned on.
• The capacity of this AC outlet is 150W. Do not
connect devices that consume electricity more than
the capacity of these AC outlets. If the total power
consumption of the connected devices exceeds the
capacity, the protection circuit shuts down the power
supply.
!1 AC INLET
Plug the supplied power cord into this AC INLET and
then into the power outlet on the wall.
This unit can be powered by 120V AC only.
!2 Preamp Outputs
(L, R, SL, SR, SBL, SBR, C)
Jacks for L (front left), R (front right), C (Center), SL
(surround left), SR (surround right), SBL (surround
back left) and SBR (surround back right).
Use these jacks for connection to external power
amplifi ers.
!3 Subwoofer Output
Connect this jack to the line level input of a powered
subwoofer. If an external subwoofer amplifi er is used,
connect this jack to the subwoofer amplifi er input.
If you are using two subwoofers, either powered or
with a 2 channel subwoofer amplifi er, connect a “Y”
connector to the subwoofer output jack and run one
cable from it to each subwoofer amplifi er.
!4 7.1 CHANNEL or AUX2 INPUT
By connecting a DVD Audio player, Super Audio CD
multichannel player, or other components that has a
multichannel port, you can playback the audio with
5.1 channel or 7.1 channel outputs.
!5 EMITTER OUT (SR8002 only)
The signals input to the IR RECEIVER IN terminals
are output to this terminal. External devices can be
controlled by connecting them to this terminal.
!6 IR RECEIVER IN (SR8002 only)
Connect to an external IR receiver.
!7
FLASHER IN (Flasher input terminal)
These terminals are to control the unit from each zone.
Connect the control signal from a Keypad, etc.
!8 DC TRIGGER output terminal
Connect a device that needs to be triggered by DC
under certain conditions (screen, power strip, etc…)
Use the system OSD setup menu to determine the
conditions by which these jack will be active.
Note:
• This output voltage is for (status) control only, It is
not suffi cient for drive capability.
!9
MULTI ROOM REMOTE IN/OUT terminals
IN: Connect to a multi-room remote control
device, available from your Marantz dealer.
OUT: Connect to the Marantz component equipped
with remote control (RC-5) terminals in Multi
zone (Multi room).
REAR PANEL
e Multiroom Outputs
(Audio output A/B, Video)
These are the audio and video output jacks for the
Multi zone (Multi room).
Connect these jacks to optional audio power
amplifi ers or video display devices to listen and view
the source selected by the multiroom system in a
remote room.
Note:
• The SR7002 does not use Multiroom audio output
B.
r MONITOR OUT
These are monitor outputs and each one includes
both composite video and S-video confi gurations.
When connecting two video monitors or televisions,
be aware that the OSD interface can be used with
both MONITOR OUT connections.
t RS-232C
The RS-232C port is to be used in conjunction with
an external controller to control the operation of the
unit by using an external device.
The RS-232C port may also be used in the future to
update the operating software of the unit so that it will
be able to support new digital audio formats and the
like as they are introduced.
q FM antenna terminal (75 ohms)
Connect an external FM antenna with a coaxial
cable, or a cable network FM source.
AM antenna and ground terminals
Connect the supplied AM loop antenna. Use the
terminals marked “AM” and “GND”. The supplied AM
loop antenna will provide good AM reception in most
areas. Position the loop antenna until you hear the
best reception.
Note:
• The SR8002 can receive HD Radio broadcasts. (See
p.70)
w COMPONENT VIDEO INPUT/
OUTPUT
If your DVD player or other device has component
video connectors, be sure to connect them to these
component video connectors on the unit. This unit
has 4 component video input connectors to obtain
the color information (Y, C
B
, C
R
) directly from the
recorded DVD signal or other video component and
two component video outputs connector to output it
directly into the matrix decoder of the display device.
By sending the pure DVD component video signal
directly, the DVD signal forgoes the extra processing
that normally would degrade the image. The result is
vastly increased image quality, with incredibly life like
colors and crisp detail.
HDMI
HDMI
Ver1.3
Ver1.3
REMOTE
REMOTE
MULTI RC
MULTI RC
rqw u it y
o
!0!1!2!4
!9@0
!8!7 !6
@3
@4
!5 !3
@2
@1
e
e