Marantz SR8001 Stereo Receiver User Manual


  Open as PDF
of 79
 
50
ENGLISH
PRESET SCAN
2 31
OK
VOL
CH
PREV
MUTE
MENU
EXIT
GUIDE
TEST
CH.SEL
LIP.SYNC
SURR
CH
MUTE
4.
AMP
AUX2
AUX1
TAPE
TUNER
CD
CD-R
MD
12
LIGHT
Learning Remote Controller
RC8001SR
1.
TUNER
D4
D5
D2
M
D1
D3
D5
2.
2.
5.
USE
PAGE
2
D4
5 64
8
0
97
MEMO
CLEAR
DISP
OSD
THX
SLEEP
5.
CLEAR
(Using the remote control unit)
1.
P
ress the TUNER button twice within two
seconds on the remote.
2.
Press the > button until PAGE2 is displayed
and press the P-SCAN (D4) on the remote.
“PRESET SCAN” appears on the front display
and then the preset station with the lowest
preset number is recalled fi rst.
3.
Preset stations are recalled in sequence (No.1
→ No.2 → etc.) for 5 seconds each.
No stored preset number will be skipped.
4.
You can fast forward the preset stations, press
the > button until PAGE4 is displayed and
press the P-SET+ (D4) continuously.
5.
When the desired preset station is received,
cancel the preset scan operation by pressing
the CLEAR button or P-SCAN (D4) on the
remote.
RECALLING A PRESET STATION
DSS
AMP
AUX2
AUX1
TAPE
TUNER
CD
CD-R
MD
VCRDVD
TV
12
LIGHT
Learning Remote Controller
RC8001SR
1.
TUNER
OK
VOL
CH
PREV
MUTE
GUIDE
LIP.SYNC
CH
MUTE
2.
(Using the SR7001)
1.
Select the desired preset station by pressing
the 1 or 2
cursor
buttons on the front panel.
(Using the remote control unit)
1.
P
ress the TUNER button twice within two
seconds on the remote.
2.
Press the > button until PAGE4 is displayed
3.
Press the P-SET+ (D4) or P-SET– (D5) button
to tune in the deseired preset station.
Or enter the preset station number with the
numeric buttons.
MANUAL PRESET MEMORY
2 31
5 64
8
0
97
MEMO
CLEAR
PREV
MUTE
MENU
EXIT
GUIDE
TEST
CH.SEL
LIP.SYNC
SURR
7.1CH
ATT
SPK-AB
DISP
OSD
THX
SLEEP
3.
2.
2 31
5 64
8
0
97
MEMO
DI
G
D
O
MultEQ
ENTER
MENU
P
URE DIRECT THX
7.1CH INPUT
MODE AUTO
MULTI
A/B
T-MODE
MEMORY CLEAR
DISPLAY
EXIT
SPEAKERS
BAND
MIC
D
IRECT
SURROUND
SPEAKER
MULTI
S
D
L
C
R
SLSSR
LFE
DIGITAL
SURROUND
V-OFFDISPMULTIAUT O TUNED STSPKR A B
NIGHT
PEAK ANALOG
DIGITAL
ATT
SLEEP
SURR DIRECT
AUTO
DISC 6.1 MTX 6.1 EQ
PCM
AAC
3.
2. 4.
(Using the SR7001)
1.
Tune into the radio station you desire (Refer to
the “MANUAL TUNING” or “AUTO TUNING”
section).
2.
Press the MEMORY button on the front panel.
“– –“ (preset number) starts blinking on the
display.
3.
Select the preset number by pressing the 1
or 2
cursor
buttons, while this is still blinking
(approx. 5 seconds)
4.
Press the MEMORY button again to enter. The
display stops blinking.
The station is now stored in the specifi ed preset
memory location.
(Using the remote control unit)
1.
Tune into the radio station you desire (Refer to
the “MANUAL TUNING” or “AUTO TUNING”
section).
2.
Press the MEMO button on the remote. “– –“
(preset number) starts blinking on the display.
3.
Enter the desired preset number by pressing
the numeric buttons.
Note:
• When entering a single digit number (2 for example),
either input “02” or just input “2” and wait for a few
seconds.
PRESET MEMORY
With this unit you can preset up to 60 FM/AM stations
in any order.
For each station, you can memorize the frequency
and reception mode if desired.
AUTO PRESET MEMORY
This function automatically scans the FM and AM
band and enters all stations with proper signal
strength into the memory.
DIGITAL
RLVIDEO
S-VIDEO
AUX 1 INPUT
AUDIO
VOLUME
UP
DOWN
STANDBY
PHONES
READY
INPUT SELECTOR
AV SURROUND RECEIVER SR8001
MultEQ
ENTER
MENU
PURE DIRECT THX
7.1CH INPUT
MODE AUTO
MULTI
A/B
T-MODE
MEMORY CLEAR
DISPLAY
EXIT
SPEAKERS
BAND
MIC
PURE DIRECT
SURROUND
SPEAKER
MULTI
DSD
POWER ON/STANDBY
L
C
R
SLSSR
LFE
DIGITAL
SURROUND
V-OFFDISPMULTIAUT O TUNED STSPKR A B
NIGHT
PEAK ANALOG
DIGITAL
ATT
SLEEP
SURR DIRECT
AUTO
DISC 6.1 MTX 6.1 EQ
PCM
AAC
2. 4.
1. 3.
5.
2.
1.
To select FM , press the BAND button on the
front panel.
2.
While pressing the MEMORY button, press the
1 cursor button.
“AUTO PRESET” will appear on the display,
and scanning starts from the lowest frequency.
3.
Each time the tuner fi nds a station, scanning
will pause and the station will be played for fi ve
seconds.
During this time, the following operations are
possible.
The band can be changed by the BAND button.
4.
If no button is pressed during this period, the
current station is memorized in location Preset
02.
If you wish to skip the current station, press the
3 cursor button during this period, this station
is skipped and auto presetting continues.
5.
Operation stops automatically when all 50
preset memory positions are fi lled or when auto
scanning attains the highest end of all bands.
If you desire to stop the auto preset memory at
anytime, press the CLEAR button.
 previous next