Filter
Top Products
47
ENGLISH
RECORDING AN ANALOG SOURCE
In normal operation, the audio or video source
selected for listening through the SR7001 is sent to
the record outputs.
This means that any program you are watching
or listening to may be recorded simply by placing
machines connected to the outputs for TAPE OUT,
CD/CDR OUT, VCR1 OUT, and DSS/VCR2 OUT in
the record mode.
To record the input source signal you are currently
watching or listening to
STANDBY
PHONES
INPUT SELECTOR
AV SURROUND RECEIVER SR8001
MENU
PURE DIRECT THX
7.1CH INPUT
MODE AUTO
MULTI
PURE DIRECT
SURROUND
SPEAK
E
MULTI
DSD
POWER ON/STANDBY
DISPMULTIAUTO TUNED
SLEEP
SURRDIRECT
AUTO
1.
DSS
AMP
AUX2
AUX1
TAPE
TUNER
CD
CD-R
MD
VCRDVD
TV
12
LIGHT
Learning Remote Controller
RC8001SR
TAPE
DSS
AUX2
AUX1
TUNER
CD
CD-R
MD
VCRDVD
TV
1.
1.
Select the input source to record by turning the
INPUT FUNCTION SELECTOR knob on the
front panel or simply press the input selector
buttons on the remote.
The input source is now selected and you may
watch or listen to it as desired.
2.
The currently selected input source signal
is output to the TAPE OUT, CD/CDR OUT,
VCR1 OUT, and DSS/VCR2 OUT outputs for
recording.
3.
Start recording to the recording component as
desired.
Recording the video from one source and
the audio from another
You can add the sound from one source to the
video of another source to make your own video
recordings.
Below is an example of recording the sound from
a compact disc player connected to CD IN and the
video from a video camera connected to VCR1 to
video cassette recorder connected to the DSS/VCR2
OUT jack.
DSS
AMP
AUX2
AUX1
TAPE
TUNER
CD
CD-R
MD
VCRDVD
TV
12
LIGHT
Learning Remote Controller
RC8001SR
AUX1
CD
2.
1.
1.
Switch the video output source to VCR1 by
simply pressing the input selector buttons on
the remote.
2.
Switch the audio input source to CD by simply
pressing the input selector buttons on the
remote.
3.
Now “CD” has been selected as the audio input
source and “VCR1” as the video input source.
Notes:
• If you change the input source during recording, you
will record the signals from the newly selected input
source.
• You cannot record the surround effects.
• Digital input signals are only output to the digital
outputs. There is no conversion from digital to
analog .
When connecting CD players and other digital
components, do not connect only the digital
terminals, but the analog ones as well.
SELECTING ANALOG AUDIO INPUT OR
DIGITAL AUDIO INPUT
AMP
AUX2
AUX1
TAPE
TUNER
CD
CD-R
MD
12
LIGHT
Learning Remote Controller
RC8001SR
AMP
D4
D5
D2
M
D1
D3
D5
VOL
CH
USE
PAGE
4
D3
If you have already assigned the digital inputs, you
can temporarily select the audio input mode for each
input source as following procedures.
Press the AMP button and press the > button until
PAGE4 is displayed. Press the A/D (D3) button.
When this button is pressed, the input mode is
switched in the following sequence.
Auto → HDMI → Digital → Analog → Auto
Auto mode:
The types of signals being input to the digital and
analog input jacks for the selected input source are
detected automatically.
If no digital signal is being input, the analog input
jacks are selected automatically.
HDMI mode:
HDMI mode can be selected only when an HDMI
input has been assigned as an input source.
When “HDMI AUDIO” under PREFERENCE of the
SETUP MENU is set to “THROUGH”, the HDMI
mode cannot be selected.
Digital mode:
The input signal is fi xed to an assigned digital input
terminal.
Analog mode:
The analog input jacks are selected.
This selection is temporary and will not be stored in
memory.
To store changes to the input mode, select “1. INPUT
SETUP” from the MAIN MENU. (See page 25)
DISPLAY MODE
PHONES
AV SURROUND RECEIVER SR8001
MultEQ
ENTER
MENU
PURE DIRECT THX
7.1CH INPUT
MODE AUTO
MULTI T-MODE
MEMORY
DISPLAY
EXIT
S
BAND
MIC
PURE DIRECT
SURROUND
SPEAKER
MULTI
DSD
L
C
R
SLSSR
LFE
DIGITAL
SURROUND
V-OFFDISPMULTIAUT O TUNED STSPKR A B
NIGHT
PEAK ANALOG
DIGITAL
ATT
SLEEP
SURR DIRECT
AUTO
DISC 6.1 MTX 6.1 EQ
PCM
AAC
2 31
5 64
8
0
97
MEMO
CLEAR
PREV
MUTE
MENU
EXIT
GUIDE
TEST
CH.SEL
LIP.SYNC
SURR
7.1CH
ATT
SPK-AB
DISP
OSD
THX
SLEEP
7
DISP
You can select the display mode for the front display
of the SR7001.
To select this mode, press the DISPLAY on the
remote control or the front panel.
When this button is pressed, the display mode is
switched in the following sequence.
Input Mode → Surround Mode → Auto display OFF
→ Display OFF → Normal Mode → Input Mode
Normal Mode:
Displays the selected input function. If the function
has been renamed using the Function Rename
feature (see page 26), the renamed name appears
on the display.
Input Mode:
Displays the input mode set via the Function Input
Setup feature (see page 25).
Surround Mode:
Displays the status of the selected surround
mode.
Auto Display Off mode:
The display is off. But, if you make a change to
the unit such as the input or surround mode, the
display will show that change, then go back to
off after about 3 seconds. When changing the
volume, it is not displayed.
Display Off mode:
The display is off completely.
Note:
• Only the DISP indicator will be illuminated on the
front display in display off condition.