Filter
Top Products
ENGLISH
11
13 Three Component-video inputs
DVD,VCR1,DSS :
Connect the Y/Cr/Cb component video outputs of each your video
product to these jacks.
14 Component Video Outputs
Connect these outputs to the component video inputs of a video
projector or monitor. When a source connected to one of the three
Component Video Inputs is selected the signal will be sent to these
jacks.
15 Multiroom Outputs (Audio L&R, Video)
Connect these jacks to the optional audio power amplifiers or video
display devices to view and listen to the source selected by the
mulitroom system in a remote room.
16 Main Amplifier Inputs:
When the jumper pins that link the Preamp Outputs with these
inputs are removed, these jacks may be used to connect an external
source to the internal amplifiers.
Front L/R and (Front L/R) are connected internally. If you desire to
use internal the 2ch amplifiers of the front L/R channels for the
surround back L & R channel, you may remove the jumper pins for
front L/R channels, and then connect between (Front L) and
preoutput of Surr Back L channel, (Front R) and preoutput of Surr
Back R channel.
An external 2channel amplifier may be connected to the preoutput of
the Front L&R channels.
(See page iii.)
17 Preamp Outputs( L,R,SL,SR,SBL,SBR,C )
When the jumper pins that link the Amplifier Inputs with these
outputs are removed, these jacks may be connected to an external
power amplifier.
18 Subwoofer Output
Connect this jack to the line level input of a powered subwoofer. If an
external subwoofer amplifier is used, connect this jack to the
subwoofer amplifier input. If you are using two subwoofers, either
powered or with a 2 channel subwoofer amplifier, connect a “Y”
connector to the subwoofer output jack and run one cable from it to
each subwoofer amplifier.
19 Six Digital Inputs ( Dig. 1 – 6)
Dig.1,2,3 (Optical), Dig.4,5,6(Coaxial):
Connect the digital output from a DVD player, HDTV receiver, LD
player or CD player to these jacks. The signal may be either a Dolby
Digital signal, DTS signal or a standard PCM digital source.
20 Digital Audio Outputs (Optical, Coaxial)
Connect these jacks to the matching digital input connector on a
digital recorder such as a CD-R or Mini Disc recorder.
21 Speaker outputs terminals
Front L, Front R, Surround L, Surround R and Center:
Connect the these jacks to the matching + or – terminals on your
speakers. When making speaker connections, always make certain
to maintain correct polarity by connecting the red (+) terminals on the
SR-19EX to the red terminals on the speaker and the black (–)
terminals on the SR-19EX to the black terminals on the speakers.
These terminals will accept bare wire or pin connectors. Additionally,
your dealer can remove the center plastic “plugs” for you and the
terminals will then accept banana plugs as well.
22 Remote control In/Out terminals
INPUT: This connection permits the IR sensor in the receiver to
serve other remote controlled devices.
Connect this jack to the “IR IN (RC-5 in)” jack on Marantz or
other compatible equipment.
OUTPUT:If the SR-19EX’s front-panel IR sensor is blocked due to
cabinet doors or other obstructions, an external IR sensor
may be used. Connect the output of the sensor to this jack.
23 MULTI ROOM Remote In/Out terminals
IN: Connect to multi-room remote control device, available from
your Marantz dealer.
OUT: Connect to the Marantz component equipped with remote
control (RC-5) terminals in another room .(Second zone).
24 AC OUTLETS
Connect the AC power cables of components such as a DVD and CD
player to these outlets. Both SWITCHED and UNSWITCHED outlets
are provided. The one marked SWITCHED provides power only when
the SR-19EX is turned on and is useful for components which you use
every time you play your system.
The one marked UNSWITCHED is always live as long as the SR-19EX
is plugged into a live outlet.
A component connected here may be left on permanently, or may be
switched off with its own power switch.
Caution:
• In order to avoid potential turn-off thumps, anything plugged in
here should be powered up before the SR-19EX is turned on.
25 AC INLET
Connect the provided detachable power cord, and connect the AC
plug to an unswitched AC wall output.