Filter
Top Products
54
KR-V888D (En/T)
Preparations
Operations
Other
Resetting the Microcomputer
If the microcomputer may malfunction (unit cannot be operated, or
shows an erroneous display) if the power cord is unplugged while the
power is ON, or due to some other external factor. If this happens,
execute the following procedure to reset the microcomputer and
return the unit to its normal operating condition.
With the power cord plugged in, turn the POWER key
OFF. Then, while holding down the ON/STANDBY key,
press POWER.
•Please note that resetting the microcomputer will clear the contents
of the memory and returns the unit to the state it was in when it left
the factory.
In case of difficulty
Amplifier
Cause
• The speaker cords are disconnected.
• VOLUME is set to the minimum position.
• MUTE is ON.
• The SPEAKERS switches are set to OFF.
• Speaker cords are short-circuited.
• The speaker cord is disconnected.
• The speaker balance is set to an extreme
position.
• The rear speaker cords and/or the center
speaker cord is disconnected.
• A surround mode has not been engaged.
• The rear and/or center volume controls are set
to the minimum level.
• The audio cord from the turntable is not con-
nected to the PHONO jacks.
• The turntable is not grounded.
• There are differnent causes for different types
of DVD players.
• A PCM source is being played back.
• The sound mode is set to "STEREO".
Remedy
• Connect them properly referring to “Connect-
ing the speakers” #
• Adjust the volume to a proper level.
• Turn OFF the MUTE. (
• Set the SPEAKERS switch(es) to ON. *
• Turn the power off, eliminate the short-
circuiting, then turn on the power again.
#
• Connect it properly referring to “Connecting
the speakers”.
• Adjust the speaker levels using the test tone.
&
• Connect it properly referring to “Connecting
the speakers”.
• Select a surround mode.
• Adjust the speaker levels using the test tone.
&
• Insert the audio cord plugs securely into the
PHONO jacks.
• Connect the grounding wire to the GND termi-
nal on the rear panel.
• With certain DVD players, the initial sound
may be intermittent.
• Press the STEREO key.
• Press the DOLBY DIGITAL key to select the
Dolby Digital (AC-3) mode.
Symptom
No sound from the speakers.
The standby indicator blinks and sound is
not output.
Sound is not output from one of the speak-
ers.
Sound is not output from the rear (sur-
round) speakers and/or the center speaker,
or their sound is very small.
A humming noise is generated when the
PHONO input selector is selected.
The initial sound is intermittent when start-
ing playback from an AC-3 source in a DVD
player.
No sound when playing a DVD.
Digital playback is not possible from Dolby
Digital (AC-3) sources.
Tuner
Cause
• No antenna is connected.
• The broadcast band is not set properly.
• The frequency of the desired station is not
tuned.
• Noise due to ignition noise from an automo-
bile.
• Noise due to interference from an electric
appliance.
• Noise due to a nearby TV set.
• The preset station belongs to a frequency that
cannot be received.
• The preset memory was cleared because the
power cord had been unplugged for a long
period of time.
Remedy
• Connect an antenna.
• Set the broadcast band properly.
• Tune the frequency of the desired station.
£
• Install the outdoor antenna away from the
road.
• Turn off the power to the appliance.
• Install the receiver farther away from the TV.
• Preset a station with a receivable frequency.
• Preset the station again.
Symptom
Radio Stations cannot be received.
Interference.
A station which was preset cannot be re-
ceived by pressing the corresponding nu-
meric key.
continued on next page