Filter
Top Products
16
EN
Speaker settings
To enable you to obtain optimum enjoyment from this model’s listening
modes, make sure to complete the speaker settings (Subwoofer, Front,
Center, Surround and Surround Back speakers) as described below.
SETUP
MULTI
CONTROL %/fi
RECEIVER
Continued to next page
MULTI CONTROL
SETUP
POWER ON/OFF
ON/STANDBY
FRONT
CENTER
REAR
4
When the “EASY SET” has been selected.
The speaker system can be complete by simply selecting the room
type and listening position. The audio will be corrected automati-
cally according to the characteristics of the KENWOOD speaker
system in use.
• The speaker setup of each models is shown as below:
KRF-V6100D: 6.1ch surround system
KRF-V5100D: 5.1ch surround system
1 Use the MULTI CONTROL knob or MULTI CONTROL %/fi keys
to select the room type and press the SETUP key.
•“ROOM TYPE” is displayed by scrolling, and then the current
setup is displayed.
Select a room type:
1 SMALL
2 MEDIUM
3 LARGE
3m (9'10-3/8")
4m (13'1-7/8")
5m (16'5-3/8")
4m (13'1-7/8")
6m (19'8-7/8")
7m (23'3/8")
SMALL
12m
2
24m
2
35m
2
MEDIUM LARGE
Note
The speaker setup with “EASY SET” may not be appropriate with
certain speaker systems or listening environment. In this case, use
“CUSTOM” for the speaker setup.
1
Turn on the power to this model by pressing POWER ON/OFF
and ON/STANDBY
or RECEIVER key.
If you want to use the remote control unit, press the TUNER,
MD/TAPE, VIDEO 1, VIDEO 2 or AUX key on the remote control
unit to set it to the receiver control mode.
2
Initiate the setup mode.
1 Press the SETUP key.
2 Use the MULTI CONTROL knob or MULTI CONTROL %/fi keys
for the following displays.
1 SP SETUP
2 TESTTONE
3 DISTANCE
4 LFE LVL
5 EXIT
The flow of the SETUP is as follows;
SP SETUP TESTTONE DISTANCE LFE LEVEL
EXIT
EXIT
L
C
R
LB
RS
RB
LS
SW
LEFT
CENTER
RIGHT
LEFT BACK SURR
RIGHT SURR
RIGHT BACK SURR
LEFT SURR
SUBWOOFER
L
C
R
RS
RB
LB
LS
SW
MANUAL
AUTO
CUSTOM
EASY SET
Subwoofer
Front
ROOM TYPE
POSITION
Center
Surround
Surround Back
Subwoofer Re-mix
(KRF-V6100D only)
• If you have selected “SPEAKER” as the Surround Back setting,
“RB”/ ”RIGHT BACK SURR” and “LB”/ ”LEFT BACK SURR” are
not appeared but ”BS” / “BACK SURR” is appeared on the display.
3
Select the setup method.
1 Select “SP SETUP” and press the SETUP key to select the
speaker setup method.
2 Use the MULTI CONTROL knob or MULTI CONTROL %/fi keys
to select “EASY SET” or “CUSTOM” and press the SETUP key
again.
1 EASY SET : Select for the simplified speaker setup according
only to the room type and listening position.
After this, continue the procedure from step 4.
2 CUSTOM : Select to set up the speakers according to the
speaker system in use. Speaker setup is required
every time after the speaker system is changed.
When the setting “CUSTOM” is selected, the
procedure skips to step 5 (When the “CUSTOM”
has been selected). &
KRF-V6100D only
Preparing for surround sound
*Indicated sizes are based on an average situation.
2 Use the MULTI CONTROL knob or MULTI CONTROL %/fi keys
to select the listening position and press the SETUP key.
•“POSITION” is displayed by scrolling, and then the current
setup is displayed.
3 Setup is complete when the “EXIT” indication appears.
4 Press the SETUP key to exit the SETUP mode.
Select a listening position:
1 FRONT
2 CENTER
3 REAR
5632_16_25_EN 06.4.20, 2:00 PM16