JVC RX-6012RSL Stereo Receiver User Manual


 
32
Specifications
Amplifier
Output Power
At Stereo operation:
Front channels: 100 W per channel, min. RMS, driven into 8
at 1 kHz with no more than 0.9% total harmonic
distortion. (IEC268-3/DIN)
At Surround operation:
Front channels: 100 W per channel, min. RMS, driven into 8
at 1 kHz with no more than 0.8% total harmonic
distortion.
Center channel:100 W, min. RMS, driven into 8 at 1 kHz,
with no more than 0.8% total harmonic
distortion.
Rear channels: 100 W per channel, min. RMS, driven into 8
at 1 kHz, with no more than 0.8% total
harmonic distortion.
Audio
Audio Input Sensitivity/Impedance (1 kHz):
CD, TAPE/CDR, TV SOUND, VCR, DVD:
220 mV/47 k
Audio Input (DIGITAL IN)* :
Coaxial: DIGITAL 1 (DVD): 0.5 V(p-p)/75
Optical: DIGITAL 2 (CD): –21 dBm to –15 dBm
(660 nm ±30 nm)
* Corresponding to Linear PCM, Dolby Digital, and DTS
Digital Surround (with sampling frequency — 32 kHz,
44.1 kHz, 48 kHz).
Audio Output Level:
TAPE/CDR, VCR: 220 mV
Signal-to-Noise Ratio (’66 IHF/DIN):
CD, TAPE/CDR, TV SOUND, VCR, DVD:
87 dB/67 dB
Frequency Response (8 ):
CD, TAPE/CDR, TV SOUND, VCR, DVD:
20 Hz to 20 kHz (±1 dB)
Tone Control:
Bass (100 Hz): ±10 dB
Treble (10 kHz): ±10 dB
Video
Video Input Sensitivity/Impedance:
Composite video: VCR, DVD: 1 V(p-p)/75
Video Output Level:
Composite video: VCR, MONITOR OUT:
1 V(p-p)/75
Synchronization: Negative
Signal-to-Noise Ratio: 45 dB
FM tuner (IHF)
Tuning Range: 87.50 MHz to 108.00 MHz
Usable Sensitivity: Monaural: 17.0 dBf (1.95 µV/75 )
50 dB Quieting Sensitivity:
Monaural: 21.3 dBf (3.2 µV/75 )
Stereo: 41.3 dBf (31.5 µV/75 )
Signal-to-Noise Ratio (IHF-A weighted):
Monaural: 78 dB at 85 dBf
Stereo: 73 dB at 85 dBf
Total Harmonic Distortion:
Monaural: 0.4% at 1 kHz
Stereo: 0.6% at 1 kHz
Stereo Separation at REC OUT: 35 dB at 1 kHz
Alternate Channel Selectivity: 60 dB: (±400 kHz)
Frequency Response: 30 Hz to 15 kHz: (+0.5 dB, –3 dB)
AM (MW/LW) tuner
Tuning Range: MW: 522 kHz to 1 629 kHz
LW: 144 kHz to 288 kHz
Usable Sensitivity: Loop antenna: 400 µV/m (MW)
Signal-to-Noise Ratio: 50 dB (100 mV/m)
General
Power Requirements: AC 230V , 50 Hz
Power Consumption: 200 W (at operation)
2 W (in standby mode)
Dimensions (W x H x D): 435 mm x 146.5 mm x 416 mm
(17
3
/16 in. x 5
13
/16 in. x 16
7
/16 in.)
Mass: 8.6 kg (19.0 lbs)
Designs & specifications are subject to change without notice.
EN28-32.RX-6010&6012R[B]_f 01.1.9, 5:58 PM32