Filter
Top Products
29
Operating JVC’s Audio/Video Components
You can operate JVC’s audio and video components with this receiver’s remote control, since control signals for JVC
components are preset in the remote control.
Operating Audio Components
IMPORTANT:
To operate JVC’s audio components using this remote control:
• You need to connect JVC audio components through the COMPU
LINK (SYNCHRO) jacks (see page 28) in addition to the
connections using cables with RCA pin plugs (see page 5).
• Aim the remote control directly at the remote sensor on the receiver.
• If you use the buttons on the front panel, the remote control will not
operate that source. To operate a source with the remote control,
the source must be selected using source selecting buttons on the
remote control.
• To operate the cassette deck or CD recorder using the COMPU
LINK remote control system, set the source name correctly. (See
page 11.)
• Refer also to the manuals supplied with your components.
Tuner
After pressing FM/AM, you can perform the following operations:
FM/AM: Alternates between FM and AM (MW/LW).
1 – 10, +10: Selects a preset channel number directly.
For channel number 5, press 5.
For channel number 15, press +10, then 5.
For channel number 20, press +10, then 10.
PTY SEARCH: Searches for a program by PTY codes.
PTY +/–: Selects the PTY codes.
DISPLAY: Shows the RDS signals.
Sound control section (Amplifier)
You can always perform the following operations:
SURROUND: Turns on or off the Surround modes —
Dolby Pro Logic, Dolby Digital, and DTS
Digital Surround.
SURROUND MODE: Selects the DSP modes.
After pressing SOUND, you can perform the following operations:
SUBWOOFER +/–: Adjusts the subwoofer output level.
CENTER +/–: Adjusts the center speaker output level.
REAR•L +/–: Adjusts the left rear speaker output level.
REAR•R +/–: Adjusts the right rear speaker output level.
EFFECT: Selects the effect level.
TEST: Turns on or off the test tone output.
Note:
After adjusting sounds, press the corresponding source selecting
button or CD-DISC to operate your target source by using the 10
keys; otherwise, the 10 keys cannot be used for operating your target
source.
CD player
After pressing CD, you can perform the following operations on the
CD player:
33
33
3: Starts playing.
44
44
4: Returns to the beginning of the current
(or previous) track.
¢¢
¢¢
¢: Skips to the beginning of the next track.
77
77
7: Stops playing.
88
88
8: Pauses playing. To release it, press
33
33
3.
1 – 10, +10: Selects a track number directly.
For track number 5, press 5.
For track number 15, press +10, then 5.
For track number 20, press +10, then 10.
For track number 30, press +10, +10, then 10.
1
7
1
REMOTE CONTROL
SURROUND
SURROUND
MODE
SOUND
TV/VIDEO
CD-DISC
1
5
– SUBWOOFER +TEST
6
54
EFFECT
– CENTER +
5
98
– REAR•L + – VCR CH +
5
TV
VCR
AUDIO
SLEEP
+10
10
– REAR•R +
MENU
ENTER
5
TAPE/CDR
FM/AM
MUTING
CD
TV SOUND
VCR
ANALOG/DIGITAL
TV VOL
TV CH
DVD
–
–
+
+
VOLUME
£
8
+
–
7/P
RM-SRX6010R
A/V CONTROL RECEIVER
32
PTY SEARCH
PTY –
+ PTY
DISPLAY
EN28-32.RX-6010&6012R[B]_f 01.1.9, 5:57 PM29