Filter
Top Products
31
English
Operating JVC’s Audio/Video Components
You can operate JVC’s audio and video components with this receiver’s remote control, since control signals for JVC
components are preset in the remote control.
IMPORTANT:
To operate JVC’s audio components using this remote control:
• You need to connect JVC audio components through the COMPU
LINK-3 (SYNCHRO) jacks (see page 25) in addition to the
connections using cables with RCA pin plugs (see page 5).
• Aim the remote control directly at the remote sensor on the
receiver.
• If you use the buttons on the front panel or the menu function to
choose a source, the remote control will not operate that source.
To operate a source with the remote control, the source must be
selected using buttons on the remote control.
• Refer also to the manuals supplied with your components.
ON SCREEN
SLEEP
ONE TOUCH
OPERATION
TV/VIDEO
321
6
54
98
7/P
+10
0
T
V
S
O
U
N
D
R
E
C
P
A
U
S
E
T
E
X
T
D
I
S
P
L
A
Y
RM-SR668XU
REMOTE CONTROL
M
U
T
I
N
G
D
V
D
M
U
L
T
I
/I
P
H
O
N
O
F
M
/A
M
D
V
D
CD
VCR
VOLUME VCR CH TV VOL. TV CH
10
SET
EXIT
CD-DISC
SOUND
CONTROL
TV VCR AUDIO
SURROUNDTESTDELAY
EFFECT – CENTER +
– REAR•L +
ENTER
RETURN
MENU
– REAR•R +100+
8
T
A
P
E
/M
D
Sound control section (Amplifier)
After pressing SOUND CONTROL, you can perform the following
operations:
SURROUND: Selects the DSP modes.
CENTER – / +: Adjusts the center speaker output level for the
Surround/DVD MULTI playback modes.
REAR•L – / +: Adjusts the left/right rear speaker output level for
the DSP modes.
Adjusts the left rear speaker output level for the
DVD MULTI playback mode.
REAR•R – / +: Adjusts the right rear speaker output level for the
DVD MULTI playback mode.
DELAY: Selects the delay time of the rear speaker sound.
(Only works when “PRO LOGIC” is selected.)
EFFECT: Selects the effect level for the DSP modes.
TEST: Turns on or off the test tone output for the
Surround mode.
Note:
After adjusting sounds, press the corresponding source selecting
button or CD-DISC to operate your target source by using 10 keys;
otherwise, 10 keys cannot be used for operating your target source.
CD player
After pressing CD, you can perform the following operations on the
CD player:
3: Starts playing.
44
44
4: Returns to the beginning of the current (or
previous) track.
¢¢
¢¢
¢: Skips to the beginning of the next track.
7: Stops playing.
8: Pauses playing. To release it, press 3.
1 – 10, +10: Selects a track number directly.
For track number 5, press 5.
For track number 15, press +10, then 5.
For track number 20, press +10, then 10.
For track number 30, press +10, +10, then 10.
CD player-changer
After pressing CD-DISC, you can perform the following operations
on a CD player-changer:
3: Starts playing.
44
44
4: Returns to the beginning of the current (or previous)
track.
¢¢
¢¢
¢: Skips to the beginning of the next track.
7: Stops playing.
8: Pauses playing. To release it, press 3.
1 – 6, 7/P: Select the number of a disc installed in a CD player-
changer.
After pressing CD, you can perform the following operations on the
CD player-changer:
1 – 10, +10: Selects a track number directly.
For track number 5, press 5.
For track number 15, press +10, then 5.
For track number 20, press +10, then 10.
For track number 30, press +10, +10, then 10.
Tuner
After pressing FM/AM, you can perform the following operations:
FM/AM: Alternates between FM and AM.
1 – 10, +10: Selects a preset channel number directly.
For channel number 5, press 5.
For channel number 15, press +10, then 5.
For channel number 20, press +10, then 10.
EN21_34.RX-669PGD[UB]/f 99.2.2, 1:40 PM31