Filter
Top Products
16
SETTING
MULTI JOG
Digital Input (DIGITAL IN) Terminal
Setting
When you use the digital input terminals, you have to register what
components are connected to which terminals (DIGITAL IN 1/2/3/
4).
Before you start, remember...
• There is a time limit in doing the following steps. If the setting is
canceled before you finish, start from step 1 again.
On the front panel ONLY:
To set the DIGITAL 1 terminal
1. Press SETTING repeatedly until
“COAX. DIG. IN” appears on the
display.
The display changes to show the current setting.
2. Turn MULTI JOG to select the
appropriate digital terminal
setting.
• As you turn it, the display changes to show the following:
1 DVD “ 1 MD “ 1 CDR “ 1 TV (or 1 DBS*) “
1 CD “ (back to the beginning)
*
If you have changed the source name from “TV SOUND” to
“DBS,” “DBS” appears.
To set the DIGITAL 2/3/4 terminal
1. Press SETTING repeatedly until
“OPT. DIG. IN” appears on the
display.
The display changes to show the current setting.
2. Turn MULTI JOG to select the
appropriate digital terminal
settings.
• As you turn it, the display changes to show
the following:
When the DIGITAL 1 is set to “DVD”
2 CD 3 MD 4 CDR “
2 MD 3 TV (or 2 DBS*) 4 CDR “
2 CD 3 TV (or 2 DBS*) 4 CDR “
2 CD 3 TV (or 2 DBS*) 4 MD “
(back to the beginning)
When the DIGITAL 1 is set to “MD”
2 DVD 3 TV (or 2 DBS*) 4 CDR “
2 CD 3 TV (or 2 DBS*) 4 CDR “
2 CD 3 TV (or 2 DBS*) 4 DVD “
2 CD 3 DVD 4 CDR “
(back to the beginning)
SETTING
DIGITAL 3 terminal setting
MULTI JOG
DIGITAL 4 terminal setting
DIGITAL 2 terminal setting
When the DIGITAL 1 is set to “CDR”
2 CD 3 TV (or 4 DBS*) 4 MD “
2 CD 3 MD 4 DVD “
2 MD 3 TV (or 4 DBS*) 4 DVD “
2 CD 3 TV (or 4 DBS*) 4 DVD “
(back to the beginning)
When the DIGITAL 1 is set to “TV” or “DBS”
2 CD 3 DVD 4 CDR “ 2 CD 3 DVD 4 MD “
2 CD 3 MD 4 CDR “ 2 MD 3 DVD 4 CDR “
(back to the beginning)
When the DIGITAL 1 is set to “CD”
2 MD 3 TV (or 3 DBS*) 4 CDR “
2 DVD 3 TV (or 3 DBS*) 4 CDR “
2 DVD 3 TV (or 3 DBS*) 4 MD “
2 DVD 3 MD 4 CDR “
(back to the beginning)
*
If you have changed the source name from “TV SOUND” to
“DBS,” “DBS” appears.
Note:
When shipped from the factory, the DIGITAL IN terminals can be used
as the digital input for the following components.
• DIGITAL 1 (coaxial): For DVD player
• DIGITAL 2 (optical): For CD player
• DIGITAL 3 (optical): For digital TV broadcast tuner
• DIGITAL 4 (optical): For CD recorder
Selecting the Analog or Digital Input
Mode
When you have connected digital source components using the
digital terminals (see page 8), you need to change the input mode for
these components to the appropriate digital input mode correctly —
AUTO/PCM, DOLBY DIGITAL, or DTS.
Before you start, remember...
• The digital input (DIGITAL IN) terminal setting should be
correctly done for the sources you want to select the digital
input mode for. Without setting this digital input terminal
correctly, you cannot change the input mode from analog input to
digital input even if you follow the procedure below.
On the front panel:
1. Turn SOURCE SELECTOR until
the source (CD, MD, TV SOUND,
DBS, DVD, or CDR/VCR2)* for
which you want to change the
input mode appears on the display.
Note:
*
Among the sources listed above, you can select the digital input
only for the sources which you have selected the digital input
terminals for. (See “Digital Input (DIGITAL IN) Terminal Setting.”)
SOURCE SELECTOR
EN10_20.RX-8000V[J]/f 00.1.12, 0:06 PM16