Filter
Top Products
47
To change the transmittable signals for
operating a CATV converter
1. Set the remote control mode to “CATV/DBS.”
2. Press and hold CATV/DBS POWER.
3. Press TV/DBS.
4. Enter manufacturer’s code (two digits) using
buttons 1–9, and 0.
See the list below to find the code.
Examples: For an RCA product, press 1, 9.
For a SONY product, press 2, 0.
5. Release CATV/DBS POWER.
After setting the remote control mode selector to “CATV/DBS,”
you can perform the following operations on the CATV
convertor :
CATV/DBS POWER Turns on and off the CATV converter.
CHANNEL +/– Changes the channels.
1 – 10, 0, 100+ (+10) Selects the channels.
The 100+ (+10) button will function as
the ENTER button if your equipment
requires pressing ENTER after
selecting a channel number.
Note:
Refer to the manual supplied with your CATV converter.
6. Try to operate your CATV converter by pressing
CATV/DBS POWER.
When your CATV converter turns on or off, you have entered
the correct code.
If there are more than one code listed for your brand of
CATV converter , try each one until the correct one is entered.
Manufacturer Codes
ECHOSTAR 21
GI JERROLD 01, 02, 03, 04, 05,
06, 07, 08
HAMLIN/REGAL 15, 16, 17, 18
PIONEER 13, 14
RCA 19
SCIENTIFIC ATLANTA 09, 10
SONY 20
ZENITH 11, 12
To change the transmittable signals for
operating another manufacturer’s VCR
1. Set the remote control mode to “AUDIO/TV/
VCR.”
2. Press and hold VCR POWER.
3. Press VCR.
4. Enter manufacturer’s code (two digits) using
buttons 1–9, and 0.
See the list below to find the code.
Examples: For a JVC product, press 0, 1.
For an NEC product, press 2, 5.
5. Release VCR POWER.
The following button can be used for operating the VCR (with
the remote control mode selector set to “AUDIO/TV/VCR”):
VCR POWER Turns on and off the VCR.
After pressing VCR or VCR CONTROL (with the remote
control mode selector set to “AUDIO/TV/VCR”), you can
perform the following operations on the VCR:
CHANNEL +/– Changes the TV channels on the VCR.
1 – 10, 0, 100+ (+10) Selects the TV channels.
The 100+ (+10) button will function
as the ENTER button if your VCR
requires pressing ENTER after
selecting a channel number.
PLAY Starts playback.
1 Rewinds a video tape.
¡ Fast winds a video tape.
STOP Stops operation.
PAUSE Pauses.
¶ REC: Starts recording or enters recording pause.
Notes:
• Refer to the manual supplied with your VCR.
• You can use either VCR button or the VCR CONTROL button to
activate the buttons listed above. If you press VCR, the playing
source also changes. On the other hand, if you press VCR
CONTROL, the playing source does not change.
6. Try to operate your VCR by pressing VCR
POWER.
When your VCR turns on or off, you have entered the correct
code.
If there are more than one code listed for your brand of
VCR, try each one until the correct one is entered.
Manufacturer Codes Manufacturer Codes
JVC 01, 02, 03 PHILIPS 09
EMERSON 11, 26 RCA 05, 06
FISHER 29 SAMSUNG 24
FUNAI 10, 14, 15, 16 SANYO 21, 22, 23
GOLD STAR 12 SHARP 27, 28
HITACHI 04 SHINTOM 30
MITSUBISHI 13 SONY 18, 19, 20
NEC 25 ZENITH 08
PANASONIC 07, 17
Manufacturers’ codes are subject to change without notice. If they
are changed, this remote control cannot operate the equipment.
Manufacturers’ codes are subject to change without
notice. If they are changed, this remote control cannot
operate the equipment.
EN41_50.RX-7000V[J]/f 00.1.12, 0:01 PM47