Filter
Top Products
33
Cassette deck
After pressing TAPE/MD, you can perform the following operations
on a cassette deck:
3: Starts playing.
11
11
1: Fast winds the tape from right to left.
¡¡
¡¡
¡: Fast winds the tape from left to right.
7: Stops operations.
8: Pauses playing. To release it, press 3.
REC PAUSE: Pauses recording temporarily. To release it, press 3.
Note:
To operate the cassette deck or MD recorder using the COMPU LINK
remote control system, set the source name correctly. (See page 11.)
MD recorder
After pressing TAPE/MD, you can perform the following operations
on the MD recorder:
3: Starts playing.
4: Returns to the beginning of the current (or previous)
track.
¢: Skips to the beginning of the next track.
7: Stops playing.
8: Pauses playing. To release it, press 3.
REC PAUSE: Pauses recording temporarily. To release it, press 3.
Note:
To operate the cassette deck or MD recorder using the COMPU LINK
remote control system, set the source name correctly. (See page 11.)
IMPORTANT:
To operate JVC’s video components using this remote control:
• You need to connect JVC video components through the AV
COMPU LINK jacks (see page 24) in addition to the connections
using cables with RCA pin plugs (see page 6).
• Some JVC VCRs can accept two types of the control signals —
remote code “A” and “B.” Before using this remote control, make
sure that the remote control code of the VCR connected to the
VCR jacks is set to code “A.”
• When using the remote control:
– For the DVD player and VCR operations, aim the remote control
directly at the remote sensor on each component, not on the
receiver.
– For the TV operations:
7 If the TV having the AV COMPU LINK terminal
“RECEIVER/AMP,” aim the remote control directly at the
remote sensor on the receiver.
7 If the TV having the AV COMPU LINK terminal “AV
COMPU LINK EX,” aim the remote control directly at the
remote sensor on the TV.
VCR
You can always perform the following operations:
VCR POWER: Turns on or off the VCR.
After pressing VCR, you can perform the following operations on
the VCR:
3: Starts playing.
1: Rewinds a tape.
¡: Fast winds a tape.
7: Stops operations.
8: Pauses playing. To release it, press 3.
REC PAUSE: Pauses recording temporarily. To release it, press 3.
CH +/–: Changes the channels on the VCR.
DVD player
After pressing DVD or DVD MULTI, you can perform the following
operations on a DVD player:
3: Starts playing.
4: Returns to the beginning of the current (or previous) track.
¢: Skips to the beginning of the next track.
7: Stops playing.
8 : Stops playing temporarily. To release it, press 3.
After pressing DVD or DVD MULTI, these buttons can be used
for the DVD menu operations.
Note:
For detailed menu operations, refer to the instructions supplied
with the discs or the DVD player.
TV
You can always perform the following operations:
TV POWER: Turns on or off the TV.
TV VOL. +/–: Adjusts the volume.
TV/VIDEO: Sets the input mode (either TV or VIDEO).
After pressing TV SOUND, you can perform the following
operations on a TV:
1 – 9, 0, 100+: Selects the channels.
RETURN: Alternates between the previously selected channel
and the current channel.
CH +/–: Changes the channels.
2
6
54
98
7/P
10
TEST
EFFECT – CENTER +
– REAR•L +
ENTER
RETURN
MENU
– REAR•R +
EN30_38.RX-668V[J]/f 99.1.16, 2:09 PM33