Filter
Top Products
21
Using the On-Screen Menus
You can use the Menus on the TV screen to control the receiver.
To use this function, you need to connect the TV to the MONITOR OUT jack on the rear panel (see page 6), and set the
TV’s input mode to the proper position to which the receiver is connected.
• When the TV’s input mode is incorrect; for example, a different video input or TV tuner mode is selected, you
cannot show the Menus on the TV screen.
On-Screen Operation buttons (on the remote control)
SLEEP
ONE TOUCH
OPERATION
TV/VIDEO
321
6
54
98
7/P
+10
0
T
V
S
O
U
N
D
R
E
C
P
A
U
S
E
T
E
X
T
D
I
S
P
L
A
Y
RM-SR668U
REMOTE CONTROL
M
U
T
I
N
G
D
V
D
M
U
L
T
I
POWER
P
H
O
N
O
F
M
/A
M
D
V
D
T
A
P
E
/
M
D
CD
VCR
VOLUME CH TV VOL. OSD
SET
EXIT
10
CD-DISC
CATV
CONTROL
SOUND
CONTROL
TVCATV/SAT VCR AUDIO
SURROUNDTESTDELAY
EFFECT – CENTER +
– REAR•L +
ENTER
RETURN
MENU
– REAR•R +100+
8
2
6
4
8
TEST
EFFECT – CENTER +
– REAR•L +
OSD
SET
EXIT
Selecting the Source to Play (Also see page 8)
1. Press OSD SET.
2, 8, 4, and 6 buttons on the 10 keys work as % / fi / @ / # for
OSD operations.
2. Press any one of % / fi / @ / #.
The MAIN MENU appears on the TV.
Note:
The on-screen display will disappear if no operation is done for
about 1 minute.
3. Press % / fi to move to “SOURCE.”
4. Press @ / # to select the source.
5. When you finish, press OSD EXIT.
The menu disappears from the TV.
Activating the DSP Modes (Also see page 19)
1. Press OSD SET.
2, 8, 4, and 6 buttons on the 10 keys work as % / fi / @ / # for
OSD operations.
2. Press any one of % / fi / @ / #.
The MAIN MENU appears on the TV.
3. Press % / fi to move
to “MODE.”
4. Press @ / # to select the
DSP mode you want to
use.
5. When you finish, press OSD EXIT.
The menu disappears from the TV.
Adjusting the Front Speaker Output Balance
(Also see page 10)
1. Press OSD SET.
2, 8, 4, and 6 buttons on the 10 keys work as % / fi / @ / # for
OSD operations.
2. Press any one of % / fi / @ / #.
The MAIN MENU appears on the TV.
3. Press % / fi to move to “SOUND
CONTROL,” then press @ / #.
The SOUND CONTROL menu appears.
4. Press % / fi to move
to “BAL.” (Balance).
5. Press @ / # to adjust
the balance.
6. When you finish, press OSD EXIT repeatedly
until the menu disappears from the TV.
Reinforcing the Bass (Also see page 10)
1. Press OSD SET.
2, 8, 4, and 6 buttons on the 10 keys work as % / fi / @ / # for
OSD operations.
2. Press any one of % / fi / @ / #.
The MAIN MENU appears on the TV.
3. Press % / fi to move to “SOUND
CONTROL,” then press @ / #.
The SOUND CONTROL menu appears.
4. Press % / fi to move
to “BASS BOOST.”
5. Press @ / # to turn the
Bass Boost function
“ON” or “OFF.”
6. When you finish, press OSD EXIT repeatedly
until the menu disappears from the TV.
Attenuating the Input Signal
(Also see page 10)
1. Press OSD SET.
2, 8, 4, and 6 buttons on the 10 keys work as % / fi / @ / # for
OSD operations.
2. Press any one of % / fi / @ / #.
The MAIN MENU appears on the TV.
3. Press % / fi to move to “SOUND
CONTROL,” then press @ / #.
The SOUND CONTROL menu appears.
Shows the buttons you
can use on the current
menu.
In this case, use % / fi to
move up and down,
and @ / # to select,
adjust or set the item.
SOUND CONTROL
SURROUND LEVEL
TONE CONTROL
BAL.:R-21
BASS BOOST :OFF
INPUT ATT :NORMAL
NEXT PAGE
:OPERATE
SOUND CONTROL
SURROUND LEVEL
TONE CONTROL
BAL.:R-21
BASS BOOST :OFF
INPUT ATT :NORMAL
NEXT PAGE
:OPERATE
EN21_29.RX-668V[J]/f 99.1.16, 2:08 PM21