Filter
Top Products
1212
1212
12
REAR PANEL
ATTENTION!
Please make all connections to your T 752 receiver with the unit powered off or unplugged. (It is also advisable to power-down or unplug all
associated components while making or breaking any signal or AC power connections.)
1 FM & AM ANTENNA: The supplied wire “dipole” FM antenna will connect to the FM connector using the supplied “balun” adapter. It will usually
work best when mounted on a vertical surface such as a wall, with arms fully outstretched forming a horizontal “T” perpendicular to the origin point
of the signal. Experiment with placement and orientation of to yield the clearest sound and lowest background noise. In areas of difficult FM
reception an external FM antenna can yield dramatic gains in quality; consult your NAD audio specialist or a professional antenna installer.
The AM loop antenna supplied with the T 752 (or a suitable replacement) is required for AM reception. Open the clip terminal lever, insert the wire
and close, ensuring that the lever locks the wire in place. Testing different positions for the antenna may improve reception; vertical orientation will
usually produce the best results. Antenna proximity to large metal objects (appliances; radiators) may impair reception, as will attempts to lengthen
the wire to the loop.
NOTE: An external AM antenna can improve long-distance reception substantially; consult your NAD audio specialist or a professional antenna
installer. Do not connect anything other than a loop antenna to the AM ANTENNA terminal. Do not remove the AM loop antenna.
2 MAIN IN/AUDIO PRE-OUTS/SUBWOOFER OUT: The T 752’s five built-in power amplifier channels will deliver excellent quality with even very
demanding, low sensitivity home-theater speaker systems. However, it is also possible to use the T 752 as a pre-amplifier with external power
amplifiers for some or all channels (remove the supplied jumpers if necessary). Unlike the five full range channels, there is no power amplifier built-
into the T 752 for a subwoofer.
For example, you might add an outboard, 2-channel (stereo) power amplifier to your system and use the T 752’s front left/right on-board channels
to power surround back speaker pair:
• Remove the black “jumpers” that bridge the FRONT-L and FRONT-R pairs of jacks labeled AUDIO PRE-OUT and MAIN IN (save the jumpers).
• Using good quality dual-RCA audio cables connect the T 752’s FRONT-L/R AUDIO PRE-OUT jacks to the left and right line-level audio inputs of your
power amplifier; now use short cables of the same type to “jump” the T 752’s L/R MAIN IN jacks to its L/R SURR.B AUDIO PRE-OUT jacks.
• Connect your main front left/right loudspeakers to the outboard power amplifier’s left/right speaker outputs; connect your surround back
loudspeakers to the T 752’s FRONT L/R speaker outputs, which are now employed for surround-back reproduction. (Observe the cautions outlined
in the “SPEAKERS” paragraphs later in this section.)
Be sure to review the “Speaker Setup” and “Channel-Balance (Test) Setup” sections, below.
Connect the SW output to a powered (“active”) subwoofer (or to a power amplifier channel driving a passive system).
SURR-B jacks supply signals from the surround-back channels if the T 752 is so configured (see “Speaker Setup,” below). Connect to one or two
channels of an appropriate external power amplifier or other amplified component to furnish amplification for one or two surround back speakers.
You NAD audio specialist will be happy to advise you.
NOTE: Never connect the T 752’s speaker outputs and the speaker outputs of an external amplifier to the same speakers.
3 MONITOR OUT: Connect to video input of the monitor/television, using quality dual-RCA and/or S-Video cables designed for video signals. In general,
the S-Video connection is superior and should be used if your TV/monitor provides the corresponding input.
NOTE: The T752 “transcodes” S-Video to composite-video signals, so that S-Video signals connected to the DVD, SAT, VCR, and VIDEO4-6 inputs
will be present at both the S-Video and composite MONITOR OUT jacks when any of these inputs is selected. This provides the convenience of
requiring only a single video connection (usually S-Video) between the T 752 and the TV/monitor.
4CD: Connect the analog stereo audio output from a CD player or other line-level audio source to this input.
23
1
15 1214
56 8
11
9
1
0
16
74
13