Insignia NS-R5101AHD-A Home Theater System User Manual


 
15
Insignia NS-R5101AHD-A AV Home Theater Receiver
www.insigniaproducts.com
To use Audyssey to set up and correct your
speakers:
1 Turn on the receiver and the connected TV.
2 On the TV, select the input to which the receiver
is connected.
3 Set the speaker setup microphone at the Main
Listening Position 1, and connect it to the
SETUP MIC jack on the front of the receiver.
The speaker setting menu appears.
4 Press ENTER.
The room correction and speaker setup starts.
Test tones are played through each speaker as
Audyssey 2EQ® Room Correction and Speaker
Setup runs. This process takes a few minutes.
Refrain from talking during measurements and
do not stand between speakers and the
microphone. Do not disconnect the speaker
setup microphone during the room correction
and speaker setup unless you want to cancel the
setup.
5 Place the setup microphone at the next
position, then press ENTER.
Audyssey 2EQ® performs more measurements.
This takes a few minutes.
6 When prompted, place the setup microphone at
the next position, then repeat step 5.
7 Use or to select an option, then press
ENTER. The options are:
Save–To save the calculated settings and exit
the room correction and speaker setup.
Cancel–To cancel the room correction and
speaker setup.
8 Disconnect the speaker setup microphone.
Error Messages
While the room correction and speaker setup is in
progress, one of the following error messages may
appear:
Retry–Try again.
Cancel–Cancel the room correction and
speaker setup.
Ambient noise is too high–The background
noise is too loud. Remove the source of the
noise and try again.
Speaker Matching Error!–The number of
speakers detected was different from that of
the first measurement. Check the speaker
connection.
Writing Error!–This message appears if saving
fails. Try saving again. If this message appears
after two or three attempts, contact your
Insignia dealer.
Speaker Detect Error–This message appears
if a speaker is not detected. No means that no
speaker was detected.
Changing the speaker settings manually
You can manually make changes to the settings
found during the room correction and speaker
setup.
See also:
“Configuring speakers (Sp Config menu)” on
page 21.
“Setting speaker distance (Sp Distance menu)”
on page 22.
“Setting the level calibration (Level Cal menu)”
on page 22.
Using the powered subwoofer
The powered subwoofer outputs very
low-frequency sound at a low volume level,
therefore it may not be detected by Audyssey 2EQ®
Room Correction and Speaker Setup.
Notes
Make the room as quiet as possible. Background
noise and Radio Frequency Interference (RFI)
can disrupt the room measurements. Close
windows, and turn off televisions, radios, air
conditioners, fluorescent lights, home
appliances, light dimmers, or other devices.
Silence the cell phone (even if it is not in use) or
place it away from all audio electronics.
The microphone picks up test tones which
played through each speaker as Audyssey 2EQ
Room Correction and Speaker Setup run.
Note
Room correction and speaker setup cannot be
performed while a pair of headphones is
connected.
Note
The on-screen setup menus only appear on a TV that
is connected to the HDMI OUT jack. If your TV is
connected to the MONITOR OUT V or COMPONENT
VIDEO OUT jacks, use the receiver’s display when
changing the settings.
SETUP MIC jack
Speaker setup microphone
Note
You can view the calculated settings for the speaker
configuration, speaker distances, and speaker levels
by using or .
Notes
When Audyssey 2EQ® Room Correction and
Speaker Setup is complete, Audyssey is set to
On and the Audyssey indicator lights.
You can cancel Audyssey 2EQ
® Room Correction
and Speaker Setup at any point in this
procedure by disconnecting the setup
microphone.
Do not connect or disconnect any speakers
during Audyssey 2EQ
® Room Correction and
Speaker Setup.
If the receiver is muted, it will be unmuted
automatically when Audyssey 2EQ
® Room
Correction and Speaker Setup starts.
Changes to the room after Audyssey 2EQ
®
Room Correction and Speaker Setup requires
that you run Audyssey 2EQ
® Room Correction
and Speaker Setup again, as room EQ
characteristics may have changed.
NS-R5101AHD-A_10-0487_MAN_.book Page 15 Friday, May 7, 2010 7:51 AM