Filter
Top Products
-E17-
Adjusting the Speaker Volume Level
This unit is set to the standard level before shipping from the
factory. You may not need adjustment.
But, depending on the size of the room and the placement of the
speakers, you may need a fine adjustment.
In this case, follow the steps below. Please use the remote
control at the listening point.
1. Press [SOURCE] to select the desired function.
2. Press [SURROUND] repeatedly to select the desired surround
mode (“DOLBY PL”, “DOLBY 3”, “THEATER” or “HALL”).
(See “Selecting the Surround Mode” on Page E16.)
3. Press [TEST TONE] on the remote control.
“TTONE” appears and “FL” blinks.
The test tone will be heard from each speaker sequentially as
follows.
Surround mode FL display (Speaker)
DOLBY PL FL (Front left speaker)
THEATHER C (Center speaker)
HALL FR (Front right speaker)
RS (Surround right speaker)
LS (Surround left speaker)
DOLBY 3 FL (Front left speaker)
C (Center speaker)
FR (Front right speaker)
P
A
U
S
E
/
S
T
E
P
P
R
E
V
N
E
X
T
-
T
U
N
E
T
U
N
E
+
REV
SLOW
FWD
SLOW
CLEAR
TRIM
DV-RM522
TEST TONE
SOURCE
FM MODEPRESET
SOUNDBASSSURROUND
MUTE
TU/BAND
ENTER
SHIFT
S
E
T
U
P
T
O
P
M
E
N
U
S
U
B
T
I
T
L
E
M
E
N
U
0
879
+10
546
213
ANGLE A.REPLAY ZOOM
AUDIO
SLEEP
TIMER ADJUST SET/CLEAR
CLOCK
VOLUME
2
SURROUND
3, 5
TEST TONE
4, 6
VOLUME
SHIFT
ENTER
b
a
1
TRIM
4. Press [VOLUME] o or p until the test tone is at a comfortable
level.
If the test tone level is not the same from each speaker, you
may need fine adjustment of the volume level. Please follow
the steps as below.
Note:
If no adjustments are made, the original display returns
after approximately 15 seconds.
1) Press [TEST TONE] to turn the test tone off.
2) Press [SURROUND] to select the desired surround
mode.
3) Press [TRIM] while holding [SHIFT] down.
“FNTL 0” appears.
4) Press [ENTER] repeatedly to select the speaker.
FL display (Speaker)
FNTL (Front left speaker)
CENT (Center speaker)
FNTR (Front right speaker)
SURR (Surround right speaker)
SURL (Surround left speaker)
SUBW (Subwoofer)
5) Press [a] or [b] to adjust the volume level.
FNTL/FNTR: “0” ~ “-10” appears.
CENT/SURR/SURL/SUBW: “+10” ~ “-10” appears.
6) Press [ENTER].
7) Repeat step 4) to 6) for another speaker, if necessary.
8) Press [TRIM] again while holding [SHIFT] down to turn it
off.
5. Press [TEST TONE] to turn the test tone off.
“TTONE” disappears.
6. Press [VOLUME] o or p to adjust the volume as desired.
Notes:
• There is no Dolby Surround effect when monaural program
material is used.
• When receiving weak FM broadcasts, switch the Dolby Pro
Logic off. The sound quality may improve.
• When headphones are connected while any of the surround
modes are selected, the surround mode is switched off
automatically. The SURROUND button does not function
while headphones are connected.
• Trimming can be set at each function respectively.