Filter
Top Products
22
3
— Use the remote for these steps.
4
— Use the receiver for these steps.
3
or
4
— Use either device for these steps.
3
or
4
To use a satellite receiver that has analog audio
output, press
SAT
, or rotate
FUNCTION
on the receiver.
I7J
I7JI7J
I7J
appears.
To use a satellite receiver that has digital audio output, press
SAT
twice, or rotate
FUNCTION
on the receiver until
I7J#EFJ
I7J#EFJI7J#EFJ
I7J#EFJ
appears.
N
NN
No
oo
ot
tt
te
ee
e:
::
: You cannot use
I7J#EFJ
I7J#EFJI7J#EFJ
I7J#EFJ
if you do not have digital audio
output. If you rotate
FUNCTION
to
I7J#EFJ
I7J#EFJI7J#EFJ
I7J#EFJ
and you do not have
digital audio output,
EFJ
EFJEFJ
EFJ
flashes.
To control the satellite receiver or cable box with the remote
control, see “Using the Remote Control to Control Additional
Components” on Page 22.
USING THE SLEEP TIMER
You can set the sleep timer to turn off the receiver after a set
period of time.
3
or
4
Repeatedly press
SLEEP
to set the sleep timer
to the desired time (
'&
'&'&
'&
,
(&
(&(&
(&
,
)&
)&)&
)&
,
*&
*&*&
*&
,
+&
+&+&
+&
,
,&
,&,&
,&
,
-&
-&-&
-&
,
.&
.&.&
.&
, or
/&
/&/&
/&
minutes
or OFF). When the desired sleep time appears, let the sleep
timer time out (do not press
SLEEP
again). The display dims
when the sleep timer is set.
To check the expired sleep time, press
SLEEP
once. The
remaining time appears. To continue the sleep time, let it time
out. To cancel the sleep timer, press
SLEEP
repeatedly until it
turns off.
The receiver turns off when the selected time has expired.
N
NN
No
oo
ot
tt
te
ee
e:
: :
: To brighten the display while the sleep timer is on, press
DIMMER
(
on the receiver).
USING THE REMOTE CONTROL TO
CONTROL ADDITIONAL COMPONENTS
You can set your remote control to control other components
such as a VCR, TV, satellite receiver or cable box.
1. Turn on the component to be programmed.
2. Look up the brand and corresponding code(s) in the code
list (see “Manufacturer’s Codes” on Page 22).
3. While holding down the appropriate source button (
VCR
,
TV
, or
SAT
) on the remote control, use the number keys to
enter the first code from the code list.
4. Release the source button, then press
POWER
. If you have
entered the correct code, the component turns off.
If the component does not turn off, repeat steps 3 and 4
and use the next code (if applicable) listed for the brand of
your component until the component responds to the
remote command.
5. Experiment with the remote control and your components
to see which buttons work. If only a few functions operate,
repeat Step 4 to see if another code operates more buttons.
N
NN
No
oo
ot
tt
te
ee
es
ss
s:
::
:
• To turn on or off the receiver when you select the VCR,
SAT, or TV function, press
POWER
twice.
• Once the manufacturer’s code for the TV is set,
MUTE
and
VOLUME +/–
can only be used in TV mode.
C
CC
Ca
aa
au
uu
ut
tt
ti
ii
io
oo
on
nn
ns
ss
s:
::
:
• This remote control might not operate on all models of the
brands shown in the “Manufacturer’s Codes” on Page 22.
• If batteries are removed from the battery compartment of
the remote, replace the batteries within 30 minutes or the
codes are lost. You must then re-enter all previously
programmed codes.
• The buttons on the remote control may not work exactly
like the component’s corresponding buttons.
MANUFACTURER’S CODES
TV Codes
Brand Codes
ABEX 272
ADMIRAL 101
AKAI 102
ALLERON 146
AMTRON 138
AOC 104,105,106,107
AUDIOVOX 138
BELCOR 104
BELL & HOWELL 101, 262
BRADFORD 138
BROCKWOOD 104
CANDLE 104, 106, 108
CELEBRITY 102
CITIZEN 104, 106, 108, 138, 205, 271
COLORTYME 104, 106
CONCERTO 104, 106
CONTEC/CONY 112, 113, 138
CRAIG 138
CROWN 138, 271
CURTIS MATHES 104, 106, 115, 185, 205, 262, 271
CXC 138
DAEWOO 104, 105, 106, 117, 118, 271
DAYTRON 104, 106, 271
DIMENSIA 185
DUMONT 104
ELECTROBAND 102