Filter
Top Products
28 SYSTEM CONFIGURATION
Continue to adjust the individual channels until
the volume level sounds the same from each
speaker. Note that adjustments should be made
with the
‹
/
›
Buttons
E
on the remote only,
NOT the main volume controls.
If you are using a sound-pressure level (SPL)
meter for precise level adjustment with the test
tone, open the main Volume Control
d
to -
15dB and set the individual output level for each
channel so that the meter reads 75dB, C-
Weighted Slow. After all settings are made turn
the main volume down.
The AVR’s EzSet feature may also be used as an
SPL meter to assist in accurate setting of the out-
put levels, when either the internal test tone or
an external source such as a test disc is used.To
use the remote as an SPL meter, follow these
steps:
1. Press and hold the SPL Select Button
e
on the remote until the red LED under the Set
Button
F
lights and the LCD screen in the
remote changes to the display shown below.
2. Press the
⁄
Navigation Button
E
once to
change the bottom line of the remote’s LCD
display to read
MANUAL SPL as shown
below.
3. Press the Set Button
F
within five seconds
to activate the remote’s manual mode, so that
it functions as an SPL meter.The right corner of
the bottom line of the remote’s display will
show the output level of the speakers as the
test tone circulates. The level will show as a
direct SPL indication between
66DB and
79DB. Below 66DB the remote will read LOW
and above 79DB it will read HIGH.
4.When you are finished with all adjustments,
press the Clear Button
X
to return the
remote to normal operation.
NOTE: The subwoofer output level is not
adjustable using the test tone. To change the
subwoofer level, follow the steps for Output Level
Trim Adjustment on page 35.
When all channels have an equal volume level,
the adjustment is complete. Now turn the
Volume
d
down to about -40dB, otherwise
the listening level may be too high as soon as the
source’s music starts to play.To exit this menu,
press the
⁄
/
¤
buttons
E
until the on-screen
›
cursor is next to the BACKTOMASTER
MENU
line, and then press the Set Button
F
to return to the MASTER MENU.
The output levels may also be adjusted at any
time using the remote control and semi-OSD sys-
tem.To adjust the output levels in this fashion,
press the Test Button
8
.As soon as the
button is pressed, the test tone will begin to
circulate as indicated earlier.The correct channel
from which the test noise should be heard will be
shown in the lower third of the video screen and
in the Main Information Display
˜
.While
the test noise is circulating, the proper channel
position will also be indicated in the
Speaker/Channel Input Indicators
Ú
by a
blinking letter within the correct channel.Turn up
the Volume
d
until you can hear the test
noise clearly.
To adjust the output level, press the
⁄
/
¤
but-
tons
E
until the desired level is shown in the
display or on screen. Once the buttons are
released, the test noise will begin to circulate
again in five seconds.
When all channels have the same output level,
turn the Volume
d
down to about -40dB, oth-
erwise the listening level may be too high as
soon as the source’s music starts to play.
Afterwards press the Test Tone Selector
8
button again to turn the test tone off and
complete the process.
IMPORTANT NOTE: The Output level adjust-
ment made will be effective for all inputs, but
only for the actual surround mode selected.To be
effective for any other mode select that mode
(with any input) and repeat the level adjustment
described above. This will also allow you to com-
pensate level differences between speakers, that
may be different with each surround mode, or to
increase or decrease the level of certain speakers
intentionally, depending on the surround mode
selected.
Note: Output level adjustment is not available
for the VMAx or Surround Off mode, as no
surround speakers are used (so level differences
between the speakers in the room cannot occur).
But to compensate level differences between
stereo, VMAx and other surround modes (inde-
pendently from the input selected) the outputs
can be adjusted with the Level Trim Adjustment
procedure, see page 35, also for the Surround Off
(Stereo) and VMAx modes.
Once the settings outlined on the previous pages
have been made, the AVR is ready for operation.
While there are some additional settings to be
made, these are best done after you have had an
opportunity to listen to a variety of sources and
different kinds of program material.These
advanced settings are described on pages 37 to
38 of this manual. In addition, any of the settings
made in the initial configuration of the unit may
be changed at any time. As you add new or dif-
ferent sources or speakers, or if you wish to
change a setting to better reflect your listening
taste, simply follow the instructions for changing
the settings for that parameter as shown in this
section.
Note that any settings changed at any time, also
when the discrete buttons are used only, will be
stored in memory in the AVR, also if it´s turned off
completely, unless it will be reset (see page 52).
Having completed the setup and configuration
process for your AVR, you are about to experience
the finest in music and home-theater listening.
Enjoy!
SET SPKR LEVELS
MANUAL SPL
System Configuration