Filter
Top Products
25 OPERATION
Operation
Basic Operation
Once you have completed the setup and config-
uration of the AVR 7000, it is simple to operate
and enjoy. The following instructions should be
followed for you to maximize your enjoyment of
your new receiver:
• When using the AVR 7000 for the first time,
you must press the Main Power Switch
1
on
the front panel to turn the unit on.This places the
unit in a Standby mode, as indicated by the
amber color of the Power Indicator
3
. Once
the unit is in Standby, you may begin a listening
session by pressing the System Power Control
2
on the front panel or the AVR Selector
b. Note that the Power Indicator
3
will
turn green.This will turn the unit on and return it
to the input source that was last used.The unit
may also be turned on from Standby by pressing
any of the Source Selector buttons on the
remote lmnç or the Source button
!
on the front panel.
NOTE: After pressing CD,TAPE or DVD buttons
c to turn the unit on, press the AVR Selector
b to have the remote control the AVR
functions.
To turn the unit off at the end of a listening
session, simply press the System Power
Control 2 on the front panel or the Power
Off Button då on the remote. Power will
be shut off to any equipment plugged into the
rear panel Switched AC Outlets ‹ and the
Power Indicator 3 will turn amber.
When the remote is used to turn the unit “off”
it is actually placing the system in a Standby
mode, as indicated by the amber color of the
Power Indicator 3.
• To program the AVR 7000 for automatic turn-
off, press the Sleep Button on the remote.
Each press of the button will increase the time
before shut down in the following sequence:
The sleep time will be displayed in the Preset
Number/Sleep Timer Indicator L and it
will count down until the time has elapsed.
When the programmed sleep time has elapsed,
the unit will automatically turn off. Note that
the front panel display will dim to one half
brightness when the Sleep function is
programmed.To cancel the Sleep function,
press and hold the Sleep Button until
the information display returns to
normal brightness and the Sleep indicator
numbers disappear.
When you will be away from home for an
extended period of time it is always a good
idea to completely turn the unit off with the
front panel Main Power Switch
1
.
NOTE: All preset memories are lost if the unit is
left turned off with the Main Power Switch
1
for more than two weeks.
Source Selection
• To select a source, press any of the Source
Selector buttons on the remote clm
nç.
• The input source may also be changed by
pressing the front-panel Input Source
Selector button !. Each press of the button
will move the input selection through the list of
available inputs.
• The front-panel Video 4 Inputs
$
may be
used to connect a device such as a video game
or camcorder to your home entertainment
system on a temporary basis.
• As the input source is changed, the new input
name will appear momentarily as an on-screen
display in the lower third of the video display.
The input name will also appear in the Main
Information Display W and a green LED will
light next to the selected input’s name in the
front-panel Input Indicators Ó.
• As the input is changed, the AVR 7000 will
automatically switch to the digital input, sur-
round mode, speaker configuration, output lev-
els, crossover frequency and night mode status
that were entered during the configuration
process for that source.
• When an audio source is selected, the last
video input used remains routed to the Video
1 Outputs h and Video Monitor Output
e. This permits simultaneous viewing and
listening to different sources.
• When a Video source is selected, the video sig-
nal for that input will be routed to the Monitor
Output jack e and will be viewable on a TV
monitor connected to the AVR 7000. If a
component video input is connected to the
DVD ¶ or Video 2 § component inputs, it
will be routed to the Component Video
Output ∞. Make certain that your TV is set to
the proper input to view the signal.
Volume Control
• Adjust the volume to a comfortable level
using the front panel Volume Control * or
remote Volume Up/Down H buttons.
• When listening in the Stereo mode, with the
surround circuits off, the Balance Control &
may be used to adjust the relative sound output
between the left front and right front speakers.
• To temporarily silence all speaker outputs
press the Mute button fI.This will inter-
rupt the output to all speakers and the head-
phone jack, but it will not affect any recording
or dubbing that may be in progress. When the
system is muted, the MUTE indicator X will
light in the Information Display Ò. Press
the Mute button fIagain to return to
normal operation.
• During a listening session you may wish to
adjust the Bass Control
#
and Treble
Control
^
to suit your listening tastes or
room acoustics.
• To set the output of the AVR 7000 so that
the output is “flat,” with the tone controls de-
activated, press the Tone Mode button 6
button once or twice so that the words Tone
Out appear momentarily in the Main
Information Display W.To return the tone
controls to an active condition, press the Tone
Mode 6 button once or twice so that the
words Tone In momentarily appear in the
Main Information Display W.
• For private listening, plug the 1/4" stereo
phone plug from a pair of stereo headphones
into the front panel Headphone Jack
4
.
Note that when the headphone’s plug is con-
nected, the word HEADPHONE will scroll
once across the Main Information Display
W and all speakers will be silenced.When the
headphone plug is removed, the audio feed to
the speakers will be restored.
Surround Mode Selection
One of the most important features of the
AVR 7000 is its ability to reproduce a full
multichannel surround sound field from digital
sources, analog matrix surround encoded
32
33
90
min
80
min
70
min
60
min
50
min
40
min
30
min
20
min
10
min
OFF
33