Filter
Top Products
19
ENGLISH
(3) Storing signals
DVD
START LEARNED/TX
SPEAKER
TUNING
BAND
TITLE
MENU/GUIDE
MODE
MEMORY
RDS
PTY
RT
USE/LEARNT.TONE MULTI DVD
SET UP
RETURN
STATUS
DISPLAY
ON SCREEN
DOLBY / DTS
SURROUND
DIRECT
DSP SIMULATION
5CH / 6CH STEREO
STEREO
INPUT MODE
ANALOG EXT.IN
MUTING
MASTER VOL.
VOLUME DISC SKIP+
SYSTEM CALL POWER
VDP TUNER SHIFT
TV/DBS PHONO
VCR-1 CD CHANNEL
VCR-2/V.AUX
TV/VCR
AVR/AVC VIDEO DVD TV
AUDIO
VDP VCR
CD
MULTI
CDR/MDTAPE
SYSTEM
SETUP
SURROUND
PARAMETER
CH SELECT
SELECT
RC-904
123
4
SET
A / B
CALL OFF
ENTER
ON
/
SOURCE
56
789
+10
0
1,5
2
3
CDR
/
TAPE
DVD
START LEARNED/TX
SPEAKER
TUNING
BAND
TITLE
MENU/GUIDE
MODE
MEMORY
RDS
PTY
RT
USE/LEARNT.TONE MULTI DVD
SET UP
RETURN
STATUS
DISPLAY
ON SCREEN
DOLBY / DTS
SURROUND
DIRECT
DSP SIMULATION
5CH / 6CH STEREO
STEREO
INPUT MODE
ANALOG EXT.IN
MUTING
MASTER VOL.
VOLUME DISC SKIP+
SYSTEM CALL POWER
VDP TUNER SHIFT
TV/DBS PHONO
VCR-1 CD CHANNEL
VCR-2/V.AUX
TV/VCR
AVR/AVC VIDEO DVD TV
AUDIO
VDP VCR
CD
MULTI
CDR/MDTAPE
SYSTEM
SETUP
SURROUND
PARAMETER
CH SELECT
SELECT
RC-904
123
4
SET
A / B
CALL OFF
ENTER
ON
/
SOURCE
56
789
+10
0
1,3
2
CDR
/
TAPE
(4) Clearing system call settings
1
Press the SET button.
• The START LED and LEARNED/TX LED both
flash.
AVR/AVC VIDEO
AUDIO
2
Press the button at which you want to store the
system call signals.
• The START LED flashes.
3
Set the mode switch to the position for the
component whose remote control signals you
want to store.
SET
DVD TV
VDP VCR
CD
MULTI
CDR/MDTAPE
4
Press the buttons whose remote control
signals you want to store one by one.
5
Press the SET button.
SET
1
Press the SET button.
SET
2
Press the button whose settings you want to
clear.
3
Press the SET button.
• The button is reset to the settings shown on
the table on page 18.
SET
NOTES:
• The remote control signals for the buttons pressed while storing the system call signals are transmitted
when the buttons are pressed, so cover the remote sensor or take other measures so that the components
do not operate while the signals are being stored.
• The LEARNED/TX LED does not light if system call signals cannot be stored at the button that you have
pressed or if you have already stored the maximum number of signals.
Clearing “learned” remote control signals
1
Press the USE/LEARN selector button with the
tip of a pen, etc., to set the learn mode.
2
To clear “learned” remote control signals, set
the slide switch to the position at which the
signals were “learned”.
AVR/AVC VIDEO
AUDIO
3
Set the slide switch to the position at which the
signals were “learned”.
DVD TV
VDP VCR
CD
MULTI
CDR/MDTAPE
4
Press the SYSTEM CALL SET button, and hold
it in for at least four seconds.
• When both the START and LEARNED/TX
LEDs light simultaneously, all the stored
codes are cleared.
Light
SET
5
Press the USE/LEARN selector button.
DVD
START LEARNED/TX
SPEAKER
TUNING
BAND
TITLE
MENU/GUIDE
MODE
MEMORY
RDS
PTY
RT
USE/LEARNT.TONE MULTI DVD
SET UP
RETURN
STATUS
DISPLAY
ON SCREEN
DOLBY / DTS
SURROUND
DIRECT
DSP SIMULATION
5CH / 6CH STEREO
STEREO
INPUT MODE
ANALOG EXT.IN
MUTING
MASTER VOL.
VOLUME DISC SKIP+
SYSTEM CALL POWER
VDP TUNER SHIFT
TV/DBS PHONO
VCR-1 CD CHANNEL
VCR-2/V.AUX
TV/VCR
AVR/AVC VIDEO DVD TV
AUDIO
VDP VCR
CD
MULTI
CDR/MDTAPE
SYSTEM
SETUP
SURROUND
PARAMETER
CH SELECT
SELECT
RC-904
123
4
SET
A / B
CALL OFF
ENTER
ON
/
SOURCE
56
789
+10
0
4
2
1,5
3
CDR
/
TAPE